| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: uas: fix urb unmapping issue when the uas device is remove during ongoing data transfer
When a UAS device is unplugged during data transfer, there is
a probability of a system panic occurring. The root cause is
an access to an invalid memory address during URB callback handling.
Specifically, this happens when the dma_direct_unmap_sg() function
is called within the usb_hcd_unmap_urb_for_dma() interface, but the
sg->dma_address field is 0 and the sg data structure has already been
freed.
The SCSI driver sends transfer commands by invoking uas_queuecommand_lck()
in uas.c, using the uas_submit_urbs() function to submit requests to USB.
Within the uas_submit_urbs() implementation, three URBs (sense_urb,
data_urb, and cmd_urb) are sequentially submitted. Device removal may
occur at any point during uas_submit_urbs execution, which may result
in URB submission failure. However, some URBs might have been successfully
submitted before the failure, and uas_submit_urbs will return the -ENODEV
error code in this case. The current error handling directly calls
scsi_done(). In the SCSI driver, this eventually triggers scsi_complete()
to invoke scsi_end_request() for releasing the sgtable. The successfully
submitted URBs, when being unlinked to giveback, call
usb_hcd_unmap_urb_for_dma() in hcd.c, leading to exceptions during sg
unmapping operations since the sg data structure has already been freed.
This patch modifies the error condition check in the uas_submit_urbs()
function. When a UAS device is removed but one or more URBs have already
been successfully submitted to USB, it avoids immediately invoking
scsi_done() and save the cmnd to devinfo->cmnd array. If the successfully
submitted URBs is completed before devinfo->resetting being set, then
the scsi_done() function will be called within uas_try_complete() after
all pending URB operations are finalized. Otherwise, the scsi_done()
function will be called within uas_zap_pending(), which is executed after
usb_kill_anchored_urbs().
The error handling only takes effect when uas_queuecommand_lck() calls
uas_submit_urbs() and returns the error value -ENODEV . In this case,
the device is disconnected, and the flow proceeds to uas_disconnect(),
where uas_zap_pending() is invoked to call uas_try_complete(). |
| In the Linux kernel, the following vulnerability has been resolved:
comedi: c6xdigio: Fix invalid PNP driver unregistration
The Comedi low-level driver "c6xdigio" seems to be for a parallel port
connected device. When the Comedi core calls the driver's Comedi
"attach" handler `c6xdigio_attach()` to configure a Comedi to use this
driver, it tries to enable the parallel port PNP resources by
registering a PNP driver with `pnp_register_driver()`, but ignores the
return value. (The `struct pnp_driver` it uses has only the `name` and
`id_table` members filled in.) The driver's Comedi "detach" handler
`c6xdigio_detach()` unconditionally unregisters the PNP driver with
`pnp_unregister_driver()`.
It is possible for `c6xdigio_attach()` to return an error before it
calls `pnp_register_driver()` and it is possible for the call to
`pnp_register_driver()` to return an error (that is ignored). In both
cases, the driver should not be calling `pnp_unregister_driver()` as it
does in `c6xdigio_detach()`. (Note that `c6xdigio_detach()` will be
called by the Comedi core if `c6xdigio_attach()` returns an error, or if
the Comedi core decides to detach the Comedi device from the driver for
some other reason.)
The unconditional call to `pnp_unregister_driver()` without a previous
successful call to `pnp_register_driver()` will cause
`driver_unregister()` to issue a warning "Unexpected driver
unregister!". This was detected by Syzbot [1].
Also, the PNP driver registration and unregistration should be done at
module init and exit time, respectively, not when attaching or detaching
Comedi devices to the driver. (There might be more than one Comedi
device being attached to the driver, although that is unlikely.)
Change the driver to do the PNP driver registration at module init time,
and the unregistration at module exit time. Since `c6xdigio_detach()`
now only calls `comedi_legacy_detach()`, remove the function and change
the Comedi driver "detach" handler to `comedi_legacy_detach`.
-------------------------------------------
[1] Syzbot sample crash report:
Unexpected driver unregister!
WARNING: CPU: 0 PID: 5970 at drivers/base/driver.c:273 driver_unregister drivers/base/driver.c:273 [inline]
WARNING: CPU: 0 PID: 5970 at drivers/base/driver.c:273 driver_unregister+0x90/0xb0 drivers/base/driver.c:270
Modules linked in:
CPU: 0 UID: 0 PID: 5970 Comm: syz.0.17 Not tainted syzkaller #0 PREEMPT(full)
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/02/2025
RIP: 0010:driver_unregister drivers/base/driver.c:273 [inline]
RIP: 0010:driver_unregister+0x90/0xb0 drivers/base/driver.c:270
Code: 48 89 ef e8 c2 e6 82 fc 48 89 df e8 3a 93 ff ff 5b 5d e9 c3 6d d9 fb e8 be 6d d9 fb 90 48 c7 c7 e0 f8 1f 8c e8 51 a2 97 fb 90 <0f> 0b 90 90 5b 5d e9 a5 6d d9 fb e8 e0 f4 41 fc eb 94 e8 d9 f4 41
RSP: 0018:ffffc9000373f9a0 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffffffff8ff24720 RCX: ffffffff817b6ee8
RDX: ffff88807c932480 RSI: ffffffff817b6ef5 RDI: 0000000000000001
RBP: 0000000000000000 R08: 0000000000000001 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000001 R12: ffffffff8ff24660
R13: dffffc0000000000 R14: 0000000000000000 R15: ffff88814cca0000
FS: 000055556dab1500(0000) GS:ffff8881249d9000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055f77f285cd0 CR3: 000000007d871000 CR4: 00000000003526f0
Call Trace:
<TASK>
comedi_device_detach_locked+0x12f/0xa50 drivers/comedi/drivers.c:207
comedi_device_detach+0x67/0xb0 drivers/comedi/drivers.c:215
comedi_device_attach+0x43d/0x900 drivers/comedi/drivers.c:1011
do_devconfig_ioctl+0x1b1/0x710 drivers/comedi/comedi_fops.c:872
comedi_unlocked_ioctl+0x165d/0x2f00 drivers/comedi/comedi_fops.c:2178
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:597 [inline]
__se_sys_ioctl fs/ioctl.c:583 [inline]
__x64_sys_ioctl+0x18e/0x210 fs/ioctl.c:583
do_syscall_x64 arch/x86/entry/syscall_64.c:63 [inline]
do_sys
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
can: gs_usb: gs_usb_receive_bulk_callback(): check actual_length before accessing header
The driver expects to receive a struct gs_host_frame in
gs_usb_receive_bulk_callback().
Use struct_group to describe the header of the struct gs_host_frame and
check that we have at least received the header before accessing any
members of it.
To resubmit the URB, do not dereference the pointer chain
"dev->parent->hf_size_rx" but use "parent->hf_size_rx" instead. Since
"urb->context" contains "parent", it is always defined, while "dev" is not
defined if the URB it too short. |
| In the Linux kernel, the following vulnerability has been resolved:
block: fix memory leak in __blkdev_issue_zero_pages
Move the fatal signal check before bio_alloc() to prevent a memory
leak when BLKDEV_ZERO_KILLABLE is set and a fatal signal is pending.
Previously, the bio was allocated before checking for a fatal signal.
If a signal was pending, the code would break out of the loop without
freeing or chaining the just-allocated bio, causing a memory leak.
This matches the pattern already used in __blkdev_issue_write_zeroes()
where the signal check precedes the allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
exfat: fix divide-by-zero in exfat_allocate_bitmap
The variable max_ra_count can be 0 in exfat_allocate_bitmap(),
which causes a divide-by-zero error in the subsequent modulo operation
(i % max_ra_count), leading to a system crash.
When max_ra_count is 0, it means that readahead is not used. This patch
load the bitmap without readahead. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd: Fix an out of bounds error in BIOS parser
The array is hardcoded to 8 in atomfirmware.h, but firmware provides
a bigger one sometimes. Deferencing the larger array causes an out
of bounds error.
commit 4fc1ba4aa589 ("drm/amd/display: fix array index out of bound error
in bios parser") fixed some of this, but there are two other cases
not covered by it. Fix those as well. |
| In the Linux kernel, the following vulnerability has been resolved:
rcu: dump vmalloc memory info safely
Currently, for double invoke call_rcu(), will dump rcu_head objects memory
info, if the objects is not allocated from the slab allocator, the
vmalloc_dump_obj() will be invoke and the vmap_area_lock spinlock need to
be held, since the call_rcu() can be invoked in interrupt context,
therefore, there is a possibility of spinlock deadlock scenarios.
And in Preempt-RT kernel, the rcutorture test also trigger the following
lockdep warning:
BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48
in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 1, name: swapper/0
preempt_count: 1, expected: 0
RCU nest depth: 1, expected: 1
3 locks held by swapper/0/1:
#0: ffffffffb534ee80 (fullstop_mutex){+.+.}-{4:4}, at: torture_init_begin+0x24/0xa0
#1: ffffffffb5307940 (rcu_read_lock){....}-{1:3}, at: rcu_torture_init+0x1ec7/0x2370
#2: ffffffffb536af40 (vmap_area_lock){+.+.}-{3:3}, at: find_vmap_area+0x1f/0x70
irq event stamp: 565512
hardirqs last enabled at (565511): [<ffffffffb379b138>] __call_rcu_common+0x218/0x940
hardirqs last disabled at (565512): [<ffffffffb5804262>] rcu_torture_init+0x20b2/0x2370
softirqs last enabled at (399112): [<ffffffffb36b2586>] __local_bh_enable_ip+0x126/0x170
softirqs last disabled at (399106): [<ffffffffb43fef59>] inet_register_protosw+0x9/0x1d0
Preemption disabled at:
[<ffffffffb58040c3>] rcu_torture_init+0x1f13/0x2370
CPU: 0 PID: 1 Comm: swapper/0 Tainted: G W 6.5.0-rc4-rt2-yocto-preempt-rt+ #15
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.16.2-0-gea1b7a073390-prebuilt.qemu.org 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x68/0xb0
dump_stack+0x14/0x20
__might_resched+0x1aa/0x280
? __pfx_rcu_torture_err_cb+0x10/0x10
rt_spin_lock+0x53/0x130
? find_vmap_area+0x1f/0x70
find_vmap_area+0x1f/0x70
vmalloc_dump_obj+0x20/0x60
mem_dump_obj+0x22/0x90
__call_rcu_common+0x5bf/0x940
? debug_smp_processor_id+0x1b/0x30
call_rcu_hurry+0x14/0x20
rcu_torture_init+0x1f82/0x2370
? __pfx_rcu_torture_leak_cb+0x10/0x10
? __pfx_rcu_torture_leak_cb+0x10/0x10
? __pfx_rcu_torture_init+0x10/0x10
do_one_initcall+0x6c/0x300
? debug_smp_processor_id+0x1b/0x30
kernel_init_freeable+0x2b9/0x540
? __pfx_kernel_init+0x10/0x10
kernel_init+0x1f/0x150
ret_from_fork+0x40/0x50
? __pfx_kernel_init+0x10/0x10
ret_from_fork_asm+0x1b/0x30
</TASK>
The previous patch fixes this by using the deadlock-safe best-effort
version of find_vm_area. However, in case of failure print the fact that
the pointer was a vmalloc pointer so that we print at least something. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: fix NULL-deref on irq uninstall
In case of early initialisation errors and on platforms that do not use
the DPU controller, the deinitilisation code can be called with the kms
pointer set to NULL.
Patchwork: https://patchwork.freedesktop.org/patch/525104/ |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mwifiex: fix memory leak in mwifiex_histogram_read()
Always free the zeroed page on return from 'mwifiex_histogram_read()'. |
| In the Linux kernel, the following vulnerability has been resolved:
ip6_vti: fix slab-use-after-free in decode_session6
When ipv6_vti device is set to the qdisc of the sfb type, the cb field
of the sent skb may be modified during enqueuing. Then,
slab-use-after-free may occur when ipv6_vti device sends IPv6 packets.
The stack information is as follows:
BUG: KASAN: slab-use-after-free in decode_session6+0x103f/0x1890
Read of size 1 at addr ffff88802e08edc2 by task swapper/0/0
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 6.4.0-next-20230707-00001-g84e2cad7f979 #410
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014
Call Trace:
<IRQ>
dump_stack_lvl+0xd9/0x150
print_address_description.constprop.0+0x2c/0x3c0
kasan_report+0x11d/0x130
decode_session6+0x103f/0x1890
__xfrm_decode_session+0x54/0xb0
vti6_tnl_xmit+0x3e6/0x1ee0
dev_hard_start_xmit+0x187/0x700
sch_direct_xmit+0x1a3/0xc30
__qdisc_run+0x510/0x17a0
__dev_queue_xmit+0x2215/0x3b10
neigh_connected_output+0x3c2/0x550
ip6_finish_output2+0x55a/0x1550
ip6_finish_output+0x6b9/0x1270
ip6_output+0x1f1/0x540
ndisc_send_skb+0xa63/0x1890
ndisc_send_rs+0x132/0x6f0
addrconf_rs_timer+0x3f1/0x870
call_timer_fn+0x1a0/0x580
expire_timers+0x29b/0x4b0
run_timer_softirq+0x326/0x910
__do_softirq+0x1d4/0x905
irq_exit_rcu+0xb7/0x120
sysvec_apic_timer_interrupt+0x97/0xc0
</IRQ>
Allocated by task 9176:
kasan_save_stack+0x22/0x40
kasan_set_track+0x25/0x30
__kasan_slab_alloc+0x7f/0x90
kmem_cache_alloc_node+0x1cd/0x410
kmalloc_reserve+0x165/0x270
__alloc_skb+0x129/0x330
netlink_sendmsg+0x9b1/0xe30
sock_sendmsg+0xde/0x190
____sys_sendmsg+0x739/0x920
___sys_sendmsg+0x110/0x1b0
__sys_sendmsg+0xf7/0x1c0
do_syscall_64+0x39/0xb0
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Freed by task 9176:
kasan_save_stack+0x22/0x40
kasan_set_track+0x25/0x30
kasan_save_free_info+0x2b/0x40
____kasan_slab_free+0x160/0x1c0
slab_free_freelist_hook+0x11b/0x220
kmem_cache_free+0xf0/0x490
skb_free_head+0x17f/0x1b0
skb_release_data+0x59c/0x850
consume_skb+0xd2/0x170
netlink_unicast+0x54f/0x7f0
netlink_sendmsg+0x926/0xe30
sock_sendmsg+0xde/0x190
____sys_sendmsg+0x739/0x920
___sys_sendmsg+0x110/0x1b0
__sys_sendmsg+0xf7/0x1c0
do_syscall_64+0x39/0xb0
entry_SYSCALL_64_after_hwframe+0x63/0xcd
The buggy address belongs to the object at ffff88802e08ed00
which belongs to the cache skbuff_small_head of size 640
The buggy address is located 194 bytes inside of
freed 640-byte region [ffff88802e08ed00, ffff88802e08ef80)
As commit f855691975bb ("xfrm6: Fix the nexthdr offset in
_decode_session6.") showed, xfrm_decode_session was originally intended
only for the receive path. IP6CB(skb)->nhoff is not set during
transmission. Therefore, set the cb field in the skb to 0 before
sending packets. |
| In the Linux kernel, the following vulnerability has been resolved:
ubi: Fix UAF wear-leveling entry in eraseblk_count_seq_show()
Wear-leveling entry could be freed in error path, which may be accessed
again in eraseblk_count_seq_show(), for example:
__erase_worker eraseblk_count_seq_show
wl = ubi->lookuptbl[*block_number]
if (wl)
wl_entry_destroy
ubi->lookuptbl[e->pnum] = NULL
kmem_cache_free(ubi_wl_entry_slab, e)
erase_count = wl->ec // UAF!
Wear-leveling entry updating/accessing in ubi->lookuptbl should be
protected by ubi->wl_lock, fix it by adding ubi->wl_lock to serialize
wl entry accessing between wl_entry_destroy() and
eraseblk_count_seq_show().
Fetch a reproducer in [Link]. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/i915: Fix NULL ptr deref by checking new_crtc_state
intel_atomic_get_new_crtc_state can return NULL, unless crtc state wasn't
obtained previously with intel_atomic_get_crtc_state, so we must check it
for NULLness here, just as in many other places, where we can't guarantee
that intel_atomic_get_crtc_state was called.
We are currently getting NULL ptr deref because of that, so this fix was
confirmed to help.
(cherry picked from commit 1d5b09f8daf859247a1ea65b0d732a24d88980d8) |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: ina2xx: avoid NULL pointer dereference on OF device match
The affected lines were resulting in a NULL pointer dereference on our
platform because the device tree contained the following list of
compatible strings:
power-sensor@40 {
compatible = "ti,ina232", "ti,ina231";
...
};
Since the driver doesn't declare a compatible string "ti,ina232", the OF
matching succeeds on "ti,ina231". But the I2C device ID info is
populated via the first compatible string, cf. modalias population in
of_i2c_get_board_info(). Since there is no "ina232" entry in the legacy
I2C device ID table either, the struct i2c_device_id *id pointer in the
probe function is NULL.
Fix this by using the already populated type variable instead, which
points to the proper driver data. Since the name is also wanted, add a
generic one to the ina2xx_config table. |
| In the Linux kernel, the following vulnerability has been resolved:
dccp: fix data-race around dp->dccps_mss_cache
dccp_sendmsg() reads dp->dccps_mss_cache before locking the socket.
Same thing in do_dccp_getsockopt().
Add READ_ONCE()/WRITE_ONCE() annotations,
and change dccp_sendmsg() to check again dccps_mss_cache
after socket is locked. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: early: xhci-dbc: Fix a potential out-of-bound memory access
If xdbc_bulk_write() fails, the values in 'buf' can be anything. So the
string is not guaranteed to be NULL terminated when xdbc_trace() is called.
Reserve an extra byte, which will be zeroed automatically because 'buf' is
a static variable, in order to avoid troubles, should it happen. |
| In the Linux kernel, the following vulnerability has been resolved:
iavf: use internal state to free traffic IRQs
If the system tries to close the netdev while iavf_reset_task() is
running, __LINK_STATE_START will be cleared and netif_running() will
return false in iavf_reinit_interrupt_scheme(). This will result in
iavf_free_traffic_irqs() not being called and a leak as follows:
[7632.489326] remove_proc_entry: removing non-empty directory 'irq/999', leaking at least 'iavf-enp24s0f0v0-TxRx-0'
[7632.490214] WARNING: CPU: 0 PID: 10 at fs/proc/generic.c:718 remove_proc_entry+0x19b/0x1b0
is shown when pci_disable_msix() is later called. Fix by using the
internal adapter state. The traffic IRQs will always exist if
state == __IAVF_RUNNING. |
| In the Linux kernel, the following vulnerability has been resolved:
netlink: annotate accesses to nlk->cb_running
Both netlink_recvmsg() and netlink_native_seq_show() read
nlk->cb_running locklessly. Use READ_ONCE() there.
Add corresponding WRITE_ONCE() to netlink_dump() and
__netlink_dump_start()
syzbot reported:
BUG: KCSAN: data-race in __netlink_dump_start / netlink_recvmsg
write to 0xffff88813ea4db59 of 1 bytes by task 28219 on cpu 0:
__netlink_dump_start+0x3af/0x4d0 net/netlink/af_netlink.c:2399
netlink_dump_start include/linux/netlink.h:308 [inline]
rtnetlink_rcv_msg+0x70f/0x8c0 net/core/rtnetlink.c:6130
netlink_rcv_skb+0x126/0x220 net/netlink/af_netlink.c:2577
rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:6192
netlink_unicast_kernel net/netlink/af_netlink.c:1339 [inline]
netlink_unicast+0x56f/0x640 net/netlink/af_netlink.c:1365
netlink_sendmsg+0x665/0x770 net/netlink/af_netlink.c:1942
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg net/socket.c:747 [inline]
sock_write_iter+0x1aa/0x230 net/socket.c:1138
call_write_iter include/linux/fs.h:1851 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x463/0x760 fs/read_write.c:584
ksys_write+0xeb/0x1a0 fs/read_write.c:637
__do_sys_write fs/read_write.c:649 [inline]
__se_sys_write fs/read_write.c:646 [inline]
__x64_sys_write+0x42/0x50 fs/read_write.c:646
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
read to 0xffff88813ea4db59 of 1 bytes by task 28222 on cpu 1:
netlink_recvmsg+0x3b4/0x730 net/netlink/af_netlink.c:2022
sock_recvmsg_nosec+0x4c/0x80 net/socket.c:1017
____sys_recvmsg+0x2db/0x310 net/socket.c:2718
___sys_recvmsg net/socket.c:2762 [inline]
do_recvmmsg+0x2e5/0x710 net/socket.c:2856
__sys_recvmmsg net/socket.c:2935 [inline]
__do_sys_recvmmsg net/socket.c:2958 [inline]
__se_sys_recvmmsg net/socket.c:2951 [inline]
__x64_sys_recvmmsg+0xe2/0x160 net/socket.c:2951
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
value changed: 0x00 -> 0x01 |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: mediatek: mt8186: Fix use-after-free in driver remove path
When devm runs function in the "remove" path for a device it runs them
in the reverse order. That means that if you have parts of your driver
that aren't using devm or are using "roll your own" devm w/
devm_add_action_or_reset() you need to keep that in mind.
The mt8186 audio driver didn't quite get this right. Specifically, in
mt8186_init_clock() it called mt8186_audsys_clk_register() and then
went on to call a bunch of other devm function. The caller of
mt8186_init_clock() used devm_add_action_or_reset() to call
mt8186_deinit_clock() but, because of the intervening devm functions,
the order was wrong.
Specifically at probe time, the order was:
1. mt8186_audsys_clk_register()
2. afe_priv->clk = devm_kcalloc(...)
3. afe_priv->clk[i] = devm_clk_get(...)
At remove time, the order (which should have been 3, 2, 1) was:
1. mt8186_audsys_clk_unregister()
3. Free all of afe_priv->clk[i]
2. Free afe_priv->clk
The above seemed to be causing a use-after-free. Luckily, it's easy to
fix this by simply using devm more correctly. Let's move the
devm_add_action_or_reset() to the right place. In addition to fixing
the use-after-free, code inspection shows that this fixes a leak
(missing call to mt8186_audsys_clk_unregister()) that would have
happened if any of the syscon_regmap_lookup_by_phandle() calls in
mt8186_init_clock() had failed. |
| In the Linux kernel, the following vulnerability has been resolved:
of: overlay: Call of_changeset_init() early
When of_overlay_fdt_apply() fails, the changeset may be partially
applied, and the caller is still expected to call of_overlay_remove() to
clean up this partial state.
However, of_overlay_apply() calls of_resolve_phandles() before
init_overlay_changeset(). Hence if the overlay fails to apply due to an
unresolved symbol, the overlay_changeset.cset.entries list is still
uninitialized, and cleanup will crash with a NULL-pointer dereference in
overlay_removal_is_ok().
Fix this by moving the call to of_changeset_init() from
init_overlay_changeset() to of_overlay_fdt_apply(), where all other
early initialization is done. |
| In the Linux kernel, the following vulnerability has been resolved:
tty: serial: samsung_tty: Fix a memory leak in s3c24xx_serial_getclk() in case of error
If clk_get_rate() fails, the clk that has just been allocated needs to be
freed. |
