| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
PCI/AER: Avoid NULL pointer dereference in aer_ratelimit()
When platform firmware supplies error information to the OS, e.g., via the
ACPI APEI GHES mechanism, it may identify an error source device that
doesn't advertise an AER Capability and therefore dev->aer_info, which
contains AER stats and ratelimiting data, is NULL.
pci_dev_aer_stats_incr() already checks dev->aer_info for NULL, but
aer_ratelimit() did not, leading to NULL pointer dereferences like this one
from the URL below:
{1}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 0
{1}[Hardware Error]: event severity: corrected
{1}[Hardware Error]: device_id: 0000:00:00.0
{1}[Hardware Error]: vendor_id: 0x8086, device_id: 0x2020
{1}[Hardware Error]: aer_cor_status: 0x00001000, aer_cor_mask: 0x00002000
BUG: kernel NULL pointer dereference, address: 0000000000000264
RIP: 0010:___ratelimit+0xc/0x1b0
pci_print_aer+0x141/0x360
aer_recover_work_func+0xb5/0x130
[8086:2020] is an Intel "Sky Lake-E DMI3 Registers" device that claims to
be a Root Port but does not advertise an AER Capability.
Add a NULL check in aer_ratelimit() to avoid the NULL pointer dereference.
Note that this also prevents ratelimiting these events from GHES.
[bhelgaas: add crash details to commit log] |
| In the Linux kernel, the following vulnerability has been resolved:
media: iris: Fix memory leak by freeing untracked persist buffer
One internal buffer which is allocated only once per session was not
being freed during session close because it was not being tracked as
part of internal buffer list which resulted in a memory leak.
Add the necessary logic to explicitly free the untracked internal buffer
during session close to ensure all allocated memory is released
properly. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/msm: Fix bootup splat with separate_gpu_drm modparam
The drm_gem_for_each_gpuvm_bo() call from lookup_vma() accesses
drm_gem_obj.gpuva.list, which is not initialized when the drm driver
does not support DRIVER_GEM_GPUVA feature. Enable it for msm_kms
drm driver to fix the splat seen when msm.separate_gpu_drm=1 modparam
is set:
[ 9.506020] Unable to handle kernel paging request at virtual address fffffffffffffff0
[ 9.523160] Mem abort info:
[ 9.523161] ESR = 0x0000000096000006
[ 9.523163] EC = 0x25: DABT (current EL), IL = 32 bits
[ 9.523165] SET = 0, FnV = 0
[ 9.523166] EA = 0, S1PTW = 0
[ 9.523167] FSC = 0x06: level 2 translation fault
[ 9.523169] Data abort info:
[ 9.523170] ISV = 0, ISS = 0x00000006, ISS2 = 0x00000000
[ 9.523171] CM = 0, WnR = 0, TnD = 0, TagAccess = 0
[ 9.523172] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
[ 9.523174] swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000ad370f000
[ 9.523176] [fffffffffffffff0] pgd=0000000000000000, p4d=0000000ad4787403, pud=0000000ad4788403, pmd=0000000000000000
[ 9.523184] Internal error: Oops: 0000000096000006 [#1] SMP
[ 9.592968] CPU: 9 UID: 0 PID: 448 Comm: (udev-worker) Not tainted 6.17.0-rc4-assorted-fix-00005-g0e9bb53a2282-dirty #3 PREEMPT
[ 9.592970] Hardware name: Qualcomm CRD, BIOS 6.0.240718.BOOT.MXF.2.4-00515-HAMOA-1 07/18/2024
[ 9.592971] pstate: a1400005 (NzCv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--)
[ 9.592973] pc : lookup_vma+0x28/0xe0 [msm]
[ 9.592996] lr : get_vma_locked+0x2c/0x128 [msm]
[ 9.763632] sp : ffff800082dab460
[ 9.763666] Call trace:
[ 9.763668] lookup_vma+0x28/0xe0 [msm] (P)
[ 9.763688] get_vma_locked+0x2c/0x128 [msm]
[ 9.763706] msm_gem_get_and_pin_iova_range+0x68/0x11c [msm]
[ 9.763723] msm_gem_get_and_pin_iova+0x18/0x24 [msm]
[ 9.763740] msm_fbdev_driver_fbdev_probe+0xd0/0x258 [msm]
[ 9.763760] __drm_fb_helper_initial_config_and_unlock+0x288/0x528 [drm_kms_helper]
[ 9.763771] drm_fb_helper_initial_config+0x44/0x54 [drm_kms_helper]
[ 9.763779] drm_fbdev_client_hotplug+0x84/0xd4 [drm_client_lib]
[ 9.763782] drm_client_register+0x58/0x9c [drm]
[ 9.763806] drm_fbdev_client_setup+0xe8/0xcf0 [drm_client_lib]
[ 9.763809] drm_client_setup+0xb4/0xd8 [drm_client_lib]
[ 9.763811] msm_drm_kms_post_init+0x2c/0x3c [msm]
[ 9.763830] msm_drm_init+0x1a8/0x22c [msm]
[ 9.763848] msm_drm_bind+0x30/0x3c [msm]
[ 9.919273] try_to_bring_up_aggregate_device+0x168/0x1d4
[ 9.919283] __component_add+0xa4/0x170
[ 9.919286] component_add+0x14/0x20
[ 9.919288] msm_dp_display_probe_tail+0x4c/0xac [msm]
[ 9.919315] msm_dp_auxbus_done_probe+0x14/0x20 [msm]
[ 9.919335] dp_aux_ep_probe+0x4c/0xf0 [drm_dp_aux_bus]
[ 9.919341] really_probe+0xbc/0x298
[ 9.919345] __driver_probe_device+0x78/0x12c
[ 9.919348] driver_probe_device+0x40/0x160
[ 9.919350] __driver_attach+0x94/0x19c
[ 9.919353] bus_for_each_dev+0x74/0xd4
[ 9.919355] driver_attach+0x24/0x30
[ 9.919358] bus_add_driver+0xe4/0x208
[ 9.919360] driver_register+0x60/0x128
[ 9.919363] __dp_aux_dp_driver_register+0x24/0x30 [drm_dp_aux_bus]
[ 9.919365] atana33xc20_init+0x20/0x1000 [panel_samsung_atna33xc20]
[ 9.919370] do_one_initcall+0x6c/0x1b0
[ 9.919374] do_init_module+0x58/0x234
[ 9.919377] load_module+0x19cc/0x1bd4
[ 9.919380] init_module_from_file+0x84/0xc4
[ 9.919382] __arm64_sys_finit_module+0x1b8/0x2cc
[ 9.919384] invoke_syscall+0x48/0x110
[ 9.919389] el0_svc_common.constprop.0+0xc8/0xe8
[ 9.919393] do_el0_svc+0x20/0x2c
[ 9.919396] el0_svc+0x34/0xf0
[ 9.919401] el0t_64_sync_handler+0xa0/0xe4
[ 9.919403] el0t_64_sync+0x198/0x19c
[ 9.919407] Code: eb0000bf 54000480 d100a003 aa0303e2 (f8418c44)
[ 9.919410] ---[ end trace 0000000000000000 ]---
Patchwork: https://patchwork.freedesktop.org/pa
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
pinctrl: rockchip: Fix refcount leak in rockchip_pinctrl_parse_groups
of_find_node_by_phandle() returns a node pointer with refcount incremented,
We should use of_node_put() on it when not needed anymore.
Add missing of_node_put() to avoid refcount leak. |
| In the Linux kernel, the following vulnerability has been resolved:
nfp: clean mc addresses in application firmware when closing port
When moving devices from one namespace to another, mc addresses are
cleaned in software while not removed from application firmware. Thus
the mc addresses are remained and will cause resource leak.
Now use `__dev_mc_unsync` to clean mc addresses when closing port. |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: microchip: Don't free uninitialized ksz_irq
If something goes wrong at setup, ksz_irq_free() can be called on
uninitialized ksz_irq (for example when ksz_ptp_irq_setup() fails). It
leads to freeing uninitialized IRQ numbers and/or domains.
Use dsa_switch_for_each_user_port_continue_reverse() in the error path
to iterate only over the fully initialized ports. |
| In the Linux kernel, the following vulnerability has been resolved:
block, bfq: Fix division by zero error on zero wsum
When the weighted sum is zero the calculation of limit causes
a division by zero error. Fix this by continuing to the next level.
This was discovered by running as root:
stress-ng --ioprio 0
Fixes divison by error oops:
[ 521.450556] divide error: 0000 [#1] SMP NOPTI
[ 521.450766] CPU: 2 PID: 2684464 Comm: stress-ng-iopri Not tainted 6.2.1-1280.native #1
[ 521.451117] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.1-0-g3208b098f51a-prebuilt.qemu.org 04/01/2014
[ 521.451627] RIP: 0010:bfqq_request_over_limit+0x207/0x400
[ 521.451875] Code: 01 48 8d 0c c8 74 0b 48 8b 82 98 00 00 00 48 8d 0c c8 8b 85 34 ff ff ff 48 89 ca 41 0f af 41 50 48 d1 ea 48 98 48 01 d0 31 d2 <48> f7 f1 41 39 41 48 89 85 34 ff ff ff 0f 8c 7b 01 00 00 49 8b 44
[ 521.452699] RSP: 0018:ffffb1af84eb3948 EFLAGS: 00010046
[ 521.452938] RAX: 000000000000003c RBX: 0000000000000000 RCX: 0000000000000000
[ 521.453262] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffffb1af84eb3978
[ 521.453584] RBP: ffffb1af84eb3a30 R08: 0000000000000001 R09: ffff8f88ab8a4ba0
[ 521.453905] R10: 0000000000000000 R11: 0000000000000001 R12: ffff8f88ab8a4b18
[ 521.454224] R13: ffff8f8699093000 R14: 0000000000000001 R15: ffffb1af84eb3970
[ 521.454549] FS: 00005640b6b0b580(0000) GS:ffff8f88b3880000(0000) knlGS:0000000000000000
[ 521.454912] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 521.455170] CR2: 00007ffcbcae4e38 CR3: 00000002e46de001 CR4: 0000000000770ee0
[ 521.455491] PKRU: 55555554
[ 521.455619] Call Trace:
[ 521.455736] <TASK>
[ 521.455837] ? bfq_request_merge+0x3a/0xc0
[ 521.456027] ? elv_merge+0x115/0x140
[ 521.456191] bfq_limit_depth+0xc8/0x240
[ 521.456366] __blk_mq_alloc_requests+0x21a/0x2c0
[ 521.456577] blk_mq_submit_bio+0x23c/0x6c0
[ 521.456766] __submit_bio+0xb8/0x140
[ 521.457236] submit_bio_noacct_nocheck+0x212/0x300
[ 521.457748] submit_bio_noacct+0x1a6/0x580
[ 521.458220] submit_bio+0x43/0x80
[ 521.458660] ext4_io_submit+0x23/0x80
[ 521.459116] ext4_do_writepages+0x40a/0xd00
[ 521.459596] ext4_writepages+0x65/0x100
[ 521.460050] do_writepages+0xb7/0x1c0
[ 521.460492] __filemap_fdatawrite_range+0xa6/0x100
[ 521.460979] file_write_and_wait_range+0xbf/0x140
[ 521.461452] ext4_sync_file+0x105/0x340
[ 521.461882] __x64_sys_fsync+0x67/0x100
[ 521.462305] ? syscall_exit_to_user_mode+0x2c/0x1c0
[ 521.462768] do_syscall_64+0x3b/0xc0
[ 521.463165] entry_SYSCALL_64_after_hwframe+0x5a/0xc4
[ 521.463621] RIP: 0033:0x5640b6c56590
[ 521.464006] Code: 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 80 3d 71 70 0e 00 00 74 17 b8 4a 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 48 c3 0f 1f 80 00 00 00 00 48 83 ec 18 89 7c |
| In the Linux kernel, the following vulnerability has been resolved:
autofs: fix memory leak of waitqueues in autofs_catatonic_mode
Syzkaller reports a memory leak:
BUG: memory leak
unreferenced object 0xffff88810b279e00 (size 96):
comm "syz-executor399", pid 3631, jiffies 4294964921 (age 23.870s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 08 9e 27 0b 81 88 ff ff ..........'.....
08 9e 27 0b 81 88 ff ff 00 00 00 00 00 00 00 00 ..'.............
backtrace:
[<ffffffff814cfc90>] kmalloc_trace+0x20/0x90 mm/slab_common.c:1046
[<ffffffff81bb75ca>] kmalloc include/linux/slab.h:576 [inline]
[<ffffffff81bb75ca>] autofs_wait+0x3fa/0x9a0 fs/autofs/waitq.c:378
[<ffffffff81bb88a7>] autofs_do_expire_multi+0xa7/0x3e0 fs/autofs/expire.c:593
[<ffffffff81bb8c33>] autofs_expire_multi+0x53/0x80 fs/autofs/expire.c:619
[<ffffffff81bb6972>] autofs_root_ioctl_unlocked+0x322/0x3b0 fs/autofs/root.c:897
[<ffffffff81bb6a95>] autofs_root_ioctl+0x25/0x30 fs/autofs/root.c:910
[<ffffffff81602a9c>] vfs_ioctl fs/ioctl.c:51 [inline]
[<ffffffff81602a9c>] __do_sys_ioctl fs/ioctl.c:870 [inline]
[<ffffffff81602a9c>] __se_sys_ioctl fs/ioctl.c:856 [inline]
[<ffffffff81602a9c>] __x64_sys_ioctl+0xfc/0x140 fs/ioctl.c:856
[<ffffffff84608225>] do_syscall_x64 arch/x86/entry/common.c:50 [inline]
[<ffffffff84608225>] do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
[<ffffffff84800087>] entry_SYSCALL_64_after_hwframe+0x63/0xcd
autofs_wait_queue structs should be freed if their wait_ctr becomes zero.
Otherwise they will be lost.
In this case an AUTOFS_IOC_EXPIRE_MULTI ioctl is done, then a new
waitqueue struct is allocated in autofs_wait(), its initial wait_ctr
equals 2. After that wait_event_killable() is interrupted (it returns
-ERESTARTSYS), so that 'wq->name.name == NULL' condition may be not
satisfied. Actually, this condition can be satisfied when
autofs_wait_release() or autofs_catatonic_mode() is called and, what is
also important, wait_ctr is decremented in those places. Upon the exit of
autofs_wait(), wait_ctr is decremented to 1. Then the unmounting process
begins: kill_sb calls autofs_catatonic_mode(), which should have freed the
waitqueues, but it only decrements its usage counter to zero which is not
a correct behaviour.
edit:imk
This description is of course not correct. The umount performed as a result
of an expire is a umount of a mount that has been automounted, it's not the
autofs mount itself. They happen independently, usually after everything
mounted within the autofs file system has been expired away. If everything
hasn't been expired away the automount daemon can still exit leaving mounts
in place. But expires done in both cases will result in a notification that
calls autofs_wait_release() with a result status. The problem case is the
summary execution of of the automount daemon. In this case any waiting
processes won't be woken up until either they are terminated or the mount
is umounted.
end edit: imk
So in catatonic mode we should free waitqueues which counter becomes zero.
edit: imk
Initially I was concerned that the calling of autofs_wait_release() and
autofs_catatonic_mode() was not mutually exclusive but that can't be the
case (obviously) because the queue entry (or entries) is removed from the
list when either of these two functions are called. Consequently the wait
entry will be freed by only one of these functions or by the woken process
in autofs_wait() depending on the order of the calls.
end edit: imk |
| In the Linux kernel, the following vulnerability has been resolved:
debugobjects: Don't wake up kswapd from fill_pool()
syzbot is reporting a lockdep warning in fill_pool() because the allocation
from debugobjects is using GFP_ATOMIC, which is (__GFP_HIGH | __GFP_KSWAPD_RECLAIM)
and therefore tries to wake up kswapd, which acquires kswapd_wait::lock.
Since fill_pool() might be called with arbitrary locks held, fill_pool()
should not assume that acquiring kswapd_wait::lock is safe.
Use __GFP_HIGH instead and remove __GFP_NORETRY as it is pointless for
!__GFP_DIRECT_RECLAIM allocation. |
| In the Linux kernel, the following vulnerability has been resolved:
spi: atmel-quadspi: Free resources even if runtime resume failed in .remove()
An early error exit in atmel_qspi_remove() doesn't prevent the device
unbind. So this results in an spi controller with an unbound parent
and unmapped register space (because devm_ioremap_resource() is undone).
So using the remaining spi controller probably results in an oops.
Instead unregister the controller unconditionally and only skip hardware
access and clk disable.
Also add a warning about resume failing and return zero unconditionally.
The latter has the only effect to suppress a less helpful error message by
the spi core. |
| In the Linux kernel, the following vulnerability has been resolved:
clk: ti: dra7-atl: Fix reference leak in of_dra7_atl_clk_probe
pm_runtime_get_sync() will increment pm usage counter.
Forgetting to putting operation will result in reference leak.
Add missing pm_runtime_put_sync in some error paths. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: qat - fix DMA transfer direction
When CONFIG_DMA_API_DEBUG is selected, while running the crypto self
test on the QAT crypto algorithms, the function add_dma_entry() reports
a warning similar to the one below, saying that overlapping mappings
are not supported. This occurs in tests where the input and the output
scatter list point to the same buffers (i.e. two different scatter lists
which point to the same chunks of memory).
The logic that implements the mapping uses the flag DMA_BIDIRECTIONAL
for both the input and the output scatter lists which leads to
overlapped write mappings. These are not supported by the DMA layer.
Fix by specifying the correct DMA transfer directions when mapping
buffers. For in-place operations where the input scatter list
matches the output scatter list, buffers are mapped once with
DMA_BIDIRECTIONAL, otherwise input buffers are mapped using the flag
DMA_TO_DEVICE and output buffers are mapped with DMA_FROM_DEVICE.
Overlapping a read mapping with a write mapping is a valid case in
dma-coherent devices like QAT.
The function that frees and unmaps the buffers, qat_alg_free_bufl()
has been changed accordingly to the changes to the mapping function.
DMA-API: 4xxx 0000:06:00.0: cacheline tracking EEXIST, overlapping mappings aren't supported
WARNING: CPU: 53 PID: 4362 at kernel/dma/debug.c:570 add_dma_entry+0x1e9/0x270
...
Call Trace:
dma_map_page_attrs+0x82/0x2d0
? preempt_count_add+0x6a/0xa0
qat_alg_sgl_to_bufl+0x45b/0x990 [intel_qat]
qat_alg_aead_dec+0x71/0x250 [intel_qat]
crypto_aead_decrypt+0x3d/0x70
test_aead_vec_cfg+0x649/0x810
? number+0x310/0x3a0
? vsnprintf+0x2a3/0x550
? scnprintf+0x42/0x70
? valid_sg_divisions.constprop.0+0x86/0xa0
? test_aead_vec+0xdf/0x120
test_aead_vec+0xdf/0x120
alg_test_aead+0x185/0x400
alg_test+0x3d8/0x500
? crypto_acomp_scomp_free_ctx+0x30/0x30
? __schedule+0x32a/0x12a0
? ttwu_queue_wakelist+0xbf/0x110
? _raw_spin_unlock_irqrestore+0x23/0x40
? try_to_wake_up+0x83/0x570
? _raw_spin_unlock_irqrestore+0x23/0x40
? __set_cpus_allowed_ptr_locked+0xea/0x1b0
? crypto_acomp_scomp_free_ctx+0x30/0x30
cryptomgr_test+0x27/0x50
kthread+0xe6/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: lpfc: Fix ioremap issues in lpfc_sli4_pci_mem_setup()
When if_type equals zero and pci_resource_start(pdev, PCI_64BIT_BAR4)
returns false, drbl_regs_memmap_p is not remapped. This passes a NULL
pointer to iounmap(), which can trigger a WARN() on certain arches.
When if_type equals six and pci_resource_start(pdev, PCI_64BIT_BAR4)
returns true, drbl_regs_memmap_p may has been remapped and
ctrl_regs_memmap_p is not remapped. This is a resource leak and passes a
NULL pointer to iounmap().
To fix these issues, we need to add null checks before iounmap(), and
change some goto labels. |
| In the Linux kernel, the following vulnerability has been resolved:
um: vector: Fix memory leak in vector_config
If the return value of the uml_parse_vector_ifspec function is NULL,
we should call kfree(params) to prevent memory leak. |
| In the Linux kernel, the following vulnerability has been resolved:
kcsan: Avoid READ_ONCE() in read_instrumented_memory()
Haibo Li reported:
| Unable to handle kernel paging request at virtual address
| ffffff802a0d8d7171
| Mem abort info:o:
| ESR = 0x9600002121
| EC = 0x25: DABT (current EL), IL = 32 bitsts
| SET = 0, FnV = 0 0
| EA = 0, S1PTW = 0 0
| FSC = 0x21: alignment fault
| Data abort info:o:
| ISV = 0, ISS = 0x0000002121
| CM = 0, WnR = 0 0
| swapper pgtable: 4k pages, 39-bit VAs, pgdp=000000002835200000
| [ffffff802a0d8d71] pgd=180000005fbf9003, p4d=180000005fbf9003,
| pud=180000005fbf9003, pmd=180000005fbe8003, pte=006800002a0d8707
| Internal error: Oops: 96000021 [#1] PREEMPT SMP
| Modules linked in:
| CPU: 2 PID: 45 Comm: kworker/u8:2 Not tainted
| 5.15.78-android13-8-g63561175bbda-dirty #1
| ...
| pc : kcsan_setup_watchpoint+0x26c/0x6bc
| lr : kcsan_setup_watchpoint+0x88/0x6bc
| sp : ffffffc00ab4b7f0
| x29: ffffffc00ab4b800 x28: ffffff80294fe588 x27: 0000000000000001
| x26: 0000000000000019 x25: 0000000000000001 x24: ffffff80294fdb80
| x23: 0000000000000000 x22: ffffffc00a70fb68 x21: ffffff802a0d8d71
| x20: 0000000000000002 x19: 0000000000000000 x18: ffffffc00a9bd060
| x17: 0000000000000001 x16: 0000000000000000 x15: ffffffc00a59f000
| x14: 0000000000000001 x13: 0000000000000000 x12: ffffffc00a70faa0
| x11: 00000000aaaaaaab x10: 0000000000000054 x9 : ffffffc00839adf8
| x8 : ffffffc009b4cf00 x7 : 0000000000000000 x6 : 0000000000000007
| x5 : 0000000000000000 x4 : 0000000000000000 x3 : ffffffc00a70fb70
| x2 : 0005ff802a0d8d71 x1 : 0000000000000000 x0 : 0000000000000000
| Call trace:
| kcsan_setup_watchpoint+0x26c/0x6bc
| __tsan_read2+0x1f0/0x234
| inflate_fast+0x498/0x750
| zlib_inflate+0x1304/0x2384
| __gunzip+0x3a0/0x45c
| gunzip+0x20/0x30
| unpack_to_rootfs+0x2a8/0x3fc
| do_populate_rootfs+0xe8/0x11c
| async_run_entry_fn+0x58/0x1bc
| process_one_work+0x3ec/0x738
| worker_thread+0x4c4/0x838
| kthread+0x20c/0x258
| ret_from_fork+0x10/0x20
| Code: b8bfc2a8 2a0803f7 14000007 d503249f (78bfc2a8) )
| ---[ end trace 613a943cb0a572b6 ]-----
The reason for this is that on certain arm64 configuration since
e35123d83ee3 ("arm64: lto: Strengthen READ_ONCE() to acquire when
CONFIG_LTO=y"), READ_ONCE() may be promoted to a full atomic acquire
instruction which cannot be used on unaligned addresses.
Fix it by avoiding READ_ONCE() in read_instrumented_memory(), and simply
forcing the compiler to do the required access by casting to the
appropriate volatile type. In terms of generated code this currently
only affects architectures that do not use the default READ_ONCE()
implementation.
The only downside is that we are not guaranteed atomicity of the access
itself, although on most architectures a plain load up to machine word
size should still be atomic (a fact the default READ_ONCE() still relies
on itself). |
| In the Linux kernel, the following vulnerability has been resolved:
ext4: verify orphan file size is not too big
In principle orphan file can be arbitrarily large. However orphan replay
needs to traverse it all and we also pin all its buffers in memory. Thus
filesystems with absurdly large orphan files can lead to big amounts of
memory consumed. Limit orphan file size to a sane value and also use
kvmalloc() for allocating array of block descriptor structures to avoid
large order allocations for sane but large orphan files. |
| In the Linux kernel, the following vulnerability has been resolved:
media: s5p-mfc: Clear workbit to handle error condition
During error on CLOSE_INSTANCE command, ctx_work_bits was not getting
cleared. During consequent mfc execution NULL pointer dereferencing of
this context led to kernel panic. This patch fixes this issue by making
sure to clear ctx_work_bits always. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: pm8001: Fix running_req for internal abort commands
Disabling the remote phy for a SATA disk causes a hang:
root@(none)$ more /sys/class/sas_phy/phy-0:0:8/target_port_protocols
sata
root@(none)$ echo 0 > sys/class/sas_phy/phy-0:0:8/enable
root@(none)$ [ 67.855950] sas: ex 500e004aaaaaaa1f phy08 change count has changed
[ 67.920585] sd 0:0:2:0: [sdc] Synchronizing SCSI cache
[ 67.925780] sd 0:0:2:0: [sdc] Synchronize Cache(10) failed: Result: hostbyte=0x04 driverbyte=DRIVER_OK
[ 67.935094] sd 0:0:2:0: [sdc] Stopping disk
[ 67.939305] sd 0:0:2:0: [sdc] Start/Stop Unit failed: Result: hostbyte=0x04 driverbyte=DRIVER_OK
...
[ 123.998998] INFO: task kworker/u192:1:642 blocked for more than 30 seconds.
[ 124.005960] Not tainted 6.0.0-rc1-205202-gf26f8f761e83 #218
[ 124.012049] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 124.019872] task:kworker/u192:1 state:D stack:0 pid: 642 ppid: 2 flags:0x00000008
[ 124.028223] Workqueue: 0000:04:00.0_event_q sas_port_event_worker
[ 124.034319] Call trace:
[ 124.036758] __switch_to+0x128/0x278
[ 124.040333] __schedule+0x434/0xa58
[ 124.043820] schedule+0x94/0x138
[ 124.047045] schedule_timeout+0x2fc/0x368
[ 124.051052] wait_for_completion+0xdc/0x200
[ 124.055234] __flush_workqueue+0x1a8/0x708
[ 124.059328] sas_porte_broadcast_rcvd+0xa8/0xc0
[ 124.063858] sas_port_event_worker+0x60/0x98
[ 124.068126] process_one_work+0x3f8/0x660
[ 124.072134] worker_thread+0x70/0x700
[ 124.075793] kthread+0x1a4/0x1b8
[ 124.079014] ret_from_fork+0x10/0x20
The issue is that the per-device running_req read in
pm8001_dev_gone_notify() never goes to zero and we never make progress.
This is caused by missing accounting for running_req for when an internal
abort command completes.
In commit 2cbbf489778e ("scsi: pm8001: Use libsas internal abort support")
we started to send internal abort commands as a proper sas_task. In this
when we deliver a sas_task to HW the per-device running_req is incremented
in pm8001_queue_command(). However it is never decremented for internal
abort commnds, so decrement in pm8001_mpi_task_abort_resp(). |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: mts64: fix possible null-ptr-defer in snd_mts64_interrupt
I got a null-ptr-defer error report when I do the following tests
on the qemu platform:
make defconfig and CONFIG_PARPORT=m, CONFIG_PARPORT_PC=m,
CONFIG_SND_MTS64=m
Then making test scripts:
cat>test_mod1.sh<<EOF
modprobe snd-mts64
modprobe snd-mts64
EOF
Executing the script, perhaps several times, we will get a null-ptr-defer
report, as follow:
syzkaller:~# ./test_mod.sh
snd_mts64: probe of snd_mts64.0 failed with error -5
modprobe: ERROR: could not insert 'snd_mts64': No such device
BUG: kernel NULL pointer dereference, address: 0000000000000000
#PF: supervisor write access in kernel mode
#PF: error_code(0x0002) - not-present page
PGD 0 P4D 0
Oops: 0002 [#1] PREEMPT SMP PTI
CPU: 0 PID: 205 Comm: modprobe Not tainted 6.1.0-rc8-00588-g76dcd734eca2 #6
Call Trace:
<IRQ>
snd_mts64_interrupt+0x24/0xa0 [snd_mts64]
parport_irq_handler+0x37/0x50 [parport]
__handle_irq_event_percpu+0x39/0x190
handle_irq_event_percpu+0xa/0x30
handle_irq_event+0x2f/0x50
handle_edge_irq+0x99/0x1b0
__common_interrupt+0x5d/0x100
common_interrupt+0xa0/0xc0
</IRQ>
<TASK>
asm_common_interrupt+0x22/0x40
RIP: 0010:_raw_write_unlock_irqrestore+0x11/0x30
parport_claim+0xbd/0x230 [parport]
snd_mts64_probe+0x14a/0x465 [snd_mts64]
platform_probe+0x3f/0xa0
really_probe+0x129/0x2c0
__driver_probe_device+0x6d/0xc0
driver_probe_device+0x1a/0xa0
__device_attach_driver+0x7a/0xb0
bus_for_each_drv+0x62/0xb0
__device_attach+0xe4/0x180
bus_probe_device+0x82/0xa0
device_add+0x550/0x920
platform_device_add+0x106/0x220
snd_mts64_attach+0x2e/0x80 [snd_mts64]
port_check+0x14/0x20 [parport]
bus_for_each_dev+0x6e/0xc0
__parport_register_driver+0x7c/0xb0 [parport]
snd_mts64_module_init+0x31/0x1000 [snd_mts64]
do_one_initcall+0x3c/0x1f0
do_init_module+0x46/0x1c6
load_module+0x1d8d/0x1e10
__do_sys_finit_module+0xa2/0xf0
do_syscall_64+0x37/0x90
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
Kernel panic - not syncing: Fatal exception in interrupt
Rebooting in 1 seconds..
The mts wa not initialized during interrupt, we add check for
mts to fix this bug. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: ice_adapter: release xa entry on adapter allocation failure
When ice_adapter_new() fails, the reserved XArray entry created by
xa_insert() is not released. This causes subsequent insertions at
the same index to return -EBUSY, potentially leading to
NULL pointer dereferences.
Reorder the operations as suggested by Przemek Kitszel:
1. Check if adapter already exists (xa_load)
2. Reserve the XArray slot (xa_reserve)
3. Allocate the adapter (ice_adapter_new)
4. Store the adapter (xa_store) |
