| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: qat - fix DMA transfer direction
When CONFIG_DMA_API_DEBUG is selected, while running the crypto self
test on the QAT crypto algorithms, the function add_dma_entry() reports
a warning similar to the one below, saying that overlapping mappings
are not supported. This occurs in tests where the input and the output
scatter list point to the same buffers (i.e. two different scatter lists
which point to the same chunks of memory).
The logic that implements the mapping uses the flag DMA_BIDIRECTIONAL
for both the input and the output scatter lists which leads to
overlapped write mappings. These are not supported by the DMA layer.
Fix by specifying the correct DMA transfer directions when mapping
buffers. For in-place operations where the input scatter list
matches the output scatter list, buffers are mapped once with
DMA_BIDIRECTIONAL, otherwise input buffers are mapped using the flag
DMA_TO_DEVICE and output buffers are mapped with DMA_FROM_DEVICE.
Overlapping a read mapping with a write mapping is a valid case in
dma-coherent devices like QAT.
The function that frees and unmaps the buffers, qat_alg_free_bufl()
has been changed accordingly to the changes to the mapping function.
DMA-API: 4xxx 0000:06:00.0: cacheline tracking EEXIST, overlapping mappings aren't supported
WARNING: CPU: 53 PID: 4362 at kernel/dma/debug.c:570 add_dma_entry+0x1e9/0x270
...
Call Trace:
dma_map_page_attrs+0x82/0x2d0
? preempt_count_add+0x6a/0xa0
qat_alg_sgl_to_bufl+0x45b/0x990 [intel_qat]
qat_alg_aead_dec+0x71/0x250 [intel_qat]
crypto_aead_decrypt+0x3d/0x70
test_aead_vec_cfg+0x649/0x810
? number+0x310/0x3a0
? vsnprintf+0x2a3/0x550
? scnprintf+0x42/0x70
? valid_sg_divisions.constprop.0+0x86/0xa0
? test_aead_vec+0xdf/0x120
test_aead_vec+0xdf/0x120
alg_test_aead+0x185/0x400
alg_test+0x3d8/0x500
? crypto_acomp_scomp_free_ctx+0x30/0x30
? __schedule+0x32a/0x12a0
? ttwu_queue_wakelist+0xbf/0x110
? _raw_spin_unlock_irqrestore+0x23/0x40
? try_to_wake_up+0x83/0x570
? _raw_spin_unlock_irqrestore+0x23/0x40
? __set_cpus_allowed_ptr_locked+0xea/0x1b0
? crypto_acomp_scomp_free_ctx+0x30/0x30
cryptomgr_test+0x27/0x50
kthread+0xe6/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30 |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/hns: Fix refcount leak in hns_roce_mmap
rdma_user_mmap_entry_get_pgoff() takes the reference.
Add missing rdma_user_mmap_entry_put() to release the reference.
Acked-by Haoyue Xu <xuhaoyue1@hisilicon.com> |
| In the Linux kernel, the following vulnerability has been resolved:
clk: st: Fix memory leak in st_of_quadfs_setup()
If st_clk_register_quadfs_pll() fails, @lock should be freed before goto
@err_exit, otherwise will cause meory leak issue, fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
media: max9286: Free control handler
The control handler is leaked in some probe-time error paths, as well as
in the remove path. Fix it. |
| In the Linux kernel, the following vulnerability has been resolved:
vfio/type1: fix cap_migration information leak
Fix an information leak where an uninitialized hole in struct
vfio_iommu_type1_info_cap_migration on the stack is exposed to userspace.
The definition of struct vfio_iommu_type1_info_cap_migration contains a hole as
shown in this pahole(1) output:
struct vfio_iommu_type1_info_cap_migration {
struct vfio_info_cap_header header; /* 0 8 */
__u32 flags; /* 8 4 */
/* XXX 4 bytes hole, try to pack */
__u64 pgsize_bitmap; /* 16 8 */
__u64 max_dirty_bitmap_size; /* 24 8 */
/* size: 32, cachelines: 1, members: 4 */
/* sum members: 28, holes: 1, sum holes: 4 */
/* last cacheline: 32 bytes */
};
The cap_mig variable is filled in without initializing the hole:
static int vfio_iommu_migration_build_caps(struct vfio_iommu *iommu,
struct vfio_info_cap *caps)
{
struct vfio_iommu_type1_info_cap_migration cap_mig;
cap_mig.header.id = VFIO_IOMMU_TYPE1_INFO_CAP_MIGRATION;
cap_mig.header.version = 1;
cap_mig.flags = 0;
/* support minimum pgsize */
cap_mig.pgsize_bitmap = (size_t)1 << __ffs(iommu->pgsize_bitmap);
cap_mig.max_dirty_bitmap_size = DIRTY_BITMAP_SIZE_MAX;
return vfio_info_add_capability(caps, &cap_mig.header, sizeof(cap_mig));
}
The structure is then copied to a temporary location on the heap. At this point
it's already too late and ioctl(VFIO_IOMMU_GET_INFO) copies it to userspace
later:
int vfio_info_add_capability(struct vfio_info_cap *caps,
struct vfio_info_cap_header *cap, size_t size)
{
struct vfio_info_cap_header *header;
header = vfio_info_cap_add(caps, size, cap->id, cap->version);
if (IS_ERR(header))
return PTR_ERR(header);
memcpy(header + 1, cap + 1, size - sizeof(*header));
return 0;
}
This issue was found by code inspection. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: sprd: Fix DMA buffer leak issue
Release DMA buffer when _probe() returns failure to avoid memory leak. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: rt2x00: Fix memory leak when handling surveys
When removing a rt2x00 device, its associated channel surveys
are not freed, causing a memory leak observable with kmemleak:
unreferenced object 0xffff9620f0881a00 (size 512):
comm "systemd-udevd", pid 2290, jiffies 4294906974 (age 33.768s)
hex dump (first 32 bytes):
70 44 12 00 00 00 00 00 92 8a 00 00 00 00 00 00 pD..............
00 00 00 00 00 00 00 00 ab 87 01 00 00 00 00 00 ................
backtrace:
[<ffffffffb0ed858b>] __kmalloc+0x4b/0x130
[<ffffffffc1b0f29b>] rt2800_probe_hw+0xc2b/0x1380 [rt2800lib]
[<ffffffffc1a9496e>] rt2800usb_probe_hw+0xe/0x60 [rt2800usb]
[<ffffffffc1ae491a>] rt2x00lib_probe_dev+0x21a/0x7d0 [rt2x00lib]
[<ffffffffc1b3b83e>] rt2x00usb_probe+0x1be/0x980 [rt2x00usb]
[<ffffffffc05981e2>] usb_probe_interface+0xe2/0x310 [usbcore]
[<ffffffffb13be2d5>] really_probe+0x1a5/0x410
[<ffffffffb13be5c8>] __driver_probe_device+0x78/0x180
[<ffffffffb13be6fe>] driver_probe_device+0x1e/0x90
[<ffffffffb13be972>] __driver_attach+0xd2/0x1c0
[<ffffffffb13bbc57>] bus_for_each_dev+0x77/0xd0
[<ffffffffb13bd2a2>] bus_add_driver+0x112/0x210
[<ffffffffb13bfc6c>] driver_register+0x5c/0x120
[<ffffffffc0596ae8>] usb_register_driver+0x88/0x150 [usbcore]
[<ffffffffb0c011c4>] do_one_initcall+0x44/0x220
[<ffffffffb0d6134c>] do_init_module+0x4c/0x220
Fix this by freeing the channel surveys on device removal.
Tested with a RT3070 based USB wireless adapter. |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: safexcel - Cleanup ring IRQ workqueues on load failure
A failure loading the safexcel driver results in the following warning
on boot, because the IRQ affinity has not been correctly cleaned up.
Ensure we clean up the affinity and workqueues on a failure to load the
driver.
crypto-safexcel: probe of f2800000.crypto failed with error -2
------------[ cut here ]------------
WARNING: CPU: 1 PID: 232 at kernel/irq/manage.c:1913 free_irq+0x300/0x340
Modules linked in: hwmon mdio_i2c crypto_safexcel(+) md5 sha256_generic libsha256 authenc libdes omap_rng rng_core nft_masq nft_nat nft_chain_nat nf_nat nft_ct nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 nf_tables libcrc32c nfnetlink fuse autofs4
CPU: 1 PID: 232 Comm: systemd-udevd Tainted: G W 6.1.6-00002-g9d4898824677 #3
Hardware name: MikroTik RB5009 (DT)
pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : free_irq+0x300/0x340
lr : free_irq+0x2e0/0x340
sp : ffff800008fa3890
x29: ffff800008fa3890 x28: 0000000000000000 x27: 0000000000000000
x26: ffff8000008e6dc0 x25: ffff000009034cac x24: ffff000009034d50
x23: 0000000000000000 x22: 000000000000004a x21: ffff0000093e0d80
x20: ffff000009034c00 x19: ffff00000615fc00 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 000075f5c1584c5e
x14: 0000000000000017 x13: 0000000000000000 x12: 0000000000000040
x11: ffff000000579b60 x10: ffff000000579b62 x9 : ffff800008bbe370
x8 : ffff000000579dd0 x7 : 0000000000000000 x6 : ffff000000579e18
x5 : ffff000000579da8 x4 : ffff800008ca0000 x3 : ffff800008ca0188
x2 : 0000000013033204 x1 : ffff000009034c00 x0 : ffff8000087eadf0
Call trace:
free_irq+0x300/0x340
devm_irq_release+0x14/0x20
devres_release_all+0xa0/0x100
device_unbind_cleanup+0x14/0x60
really_probe+0x198/0x2d4
__driver_probe_device+0x74/0xdc
driver_probe_device+0x3c/0x110
__driver_attach+0x8c/0x190
bus_for_each_dev+0x6c/0xc0
driver_attach+0x20/0x30
bus_add_driver+0x148/0x1fc
driver_register+0x74/0x120
__platform_driver_register+0x24/0x30
safexcel_init+0x48/0x1000 [crypto_safexcel]
do_one_initcall+0x4c/0x1b0
do_init_module+0x44/0x1cc
load_module+0x1724/0x1be4
__do_sys_finit_module+0xbc/0x110
__arm64_sys_finit_module+0x1c/0x24
invoke_syscall+0x44/0x110
el0_svc_common.constprop.0+0xc0/0xe0
do_el0_svc+0x20/0x80
el0_svc+0x14/0x4c
el0t_64_sync_handler+0xb0/0xb4
el0t_64_sync+0x148/0x14c
---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
md/raid10: fix memleak for 'conf->bio_split'
In the error path of raid10_run(), 'conf' need be freed, however,
'conf->bio_split' is missed and memory will be leaked.
Since there are 3 places to free 'conf', factor out a helper to fix the
problem. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: sc16is7xx: setup GPIO controller later in probe
The GPIO controller component of the sc16is7xx driver is setup too
early, which can result in a race condition where another device tries
to utilise the GPIO lines before the sc16is7xx device has finished
initialising.
This issue manifests itself as an Oops when the GPIO lines are configured:
Unable to handle kernel read from unreadable memory at virtual address
...
pc : sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx]
lr : sc16is7xx_gpio_direction_output+0x4c/0x108 [sc16is7xx]
...
Call trace:
sc16is7xx_gpio_direction_output+0x68/0x108 [sc16is7xx]
gpiod_direction_output_raw_commit+0x64/0x318
gpiod_direction_output+0xb0/0x170
create_gpio_led+0xec/0x198
gpio_led_probe+0x16c/0x4f0
platform_drv_probe+0x5c/0xb0
really_probe+0xe8/0x448
driver_probe_device+0xe8/0x138
__device_attach_driver+0x94/0x118
bus_for_each_drv+0x8c/0xe0
__device_attach+0x100/0x1b8
device_initial_probe+0x28/0x38
bus_probe_device+0xa4/0xb0
deferred_probe_work_func+0x90/0xe0
process_one_work+0x1c4/0x480
worker_thread+0x54/0x430
kthread+0x138/0x150
ret_from_fork+0x10/0x1c
This patch moves the setup of the GPIO controller functions to later in the
probe function, ensuring the sc16is7xx device has already finished
initialising by the time other devices try to make use of the GPIO lines.
The error handling has also been reordered to reflect the new
initialisation order. |
| In the Linux kernel, the following vulnerability has been resolved:
s390/dcssblk: fix kernel crash with list_add corruption
Commit fb08a1908cb1 ("dax: simplify the dax_device <-> gendisk
association") introduced new logic for gendisk association, requiring
drivers to explicitly call dax_add_host() and dax_remove_host().
For dcssblk driver, some dax_remove_host() calls were missing, e.g. in
device remove path. The commit also broke error handling for out_dax case
in device add path, resulting in an extra put_device() w/o the previous
get_device() in that case.
This lead to stale xarray entries after device add / remove cycles. In the
case when a previously used struct gendisk pointer (xarray index) would be
used again, because blk_alloc_disk() happened to return such a pointer, the
xa_insert() in dax_add_host() would fail and go to out_dax, doing the extra
put_device() in the error path. In combination with an already flawed error
handling in dcssblk (device_register() cleanup), which needs to be
addressed in a separate patch, this resulted in a missing device_del() /
klist_del(), and eventually in the kernel crash with list_add corruption on
a subsequent device_add() / klist_add().
Fix this by adding the missing dax_remove_host() calls, and also move the
put_device() in the error path to restore the previous logic. |
| In the Linux kernel, the following vulnerability has been resolved:
net: nsh: Use correct mac_offset to unwind gso skb in nsh_gso_segment()
As the call trace shows, skb_panic was caused by wrong skb->mac_header
in nsh_gso_segment():
invalid opcode: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 3 PID: 2737 Comm: syz Not tainted 6.3.0-next-20230505 #1
RIP: 0010:skb_panic+0xda/0xe0
call Trace:
skb_push+0x91/0xa0
nsh_gso_segment+0x4f3/0x570
skb_mac_gso_segment+0x19e/0x270
__skb_gso_segment+0x1e8/0x3c0
validate_xmit_skb+0x452/0x890
validate_xmit_skb_list+0x99/0xd0
sch_direct_xmit+0x294/0x7c0
__dev_queue_xmit+0x16f0/0x1d70
packet_xmit+0x185/0x210
packet_snd+0xc15/0x1170
packet_sendmsg+0x7b/0xa0
sock_sendmsg+0x14f/0x160
The root cause is:
nsh_gso_segment() use skb->network_header - nhoff to reset mac_header
in skb_gso_error_unwind() if inner-layer protocol gso fails.
However, skb->network_header may be reset by inner-layer protocol
gso function e.g. mpls_gso_segment. skb->mac_header reset by the
inaccurate network_header will be larger than skb headroom.
nsh_gso_segment
nhoff = skb->network_header - skb->mac_header;
__skb_pull(skb,nsh_len)
skb_mac_gso_segment
mpls_gso_segment
skb_reset_network_header(skb);//skb->network_header+=nsh_len
return -EINVAL;
skb_gso_error_unwind
skb_push(skb, nsh_len);
skb->mac_header = skb->network_header - nhoff;
// skb->mac_header > skb->headroom, cause skb_push panic
Use correct mac_offset to restore mac_header and get rid of nhoff. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: rndis_host: Secure rndis_query check against int overflow
Variables off and len typed as uint32 in rndis_query function
are controlled by incoming RNDIS response message thus their
value may be manipulated. Setting off to a unexpectetly large
value will cause the sum with len and 8 to overflow and pass
the implemented validation step. Consequently the response
pointer will be referring to a location past the expected
buffer boundaries allowing information leakage e.g. via
RNDIS_OID_802_3_PERMANENT_ADDRESS OID. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Fix DMA-API call trace on NVMe LS requests
The following message and call trace was seen with debug kernels:
DMA-API: qla2xxx 0000:41:00.0: device driver failed to check map
error [device address=0x00000002a3ff38d8] [size=1024 bytes] [mapped as
single]
WARNING: CPU: 0 PID: 2930 at kernel/dma/debug.c:1017
check_unmap+0xf42/0x1990
Call Trace:
debug_dma_unmap_page+0xc9/0x100
qla_nvme_ls_unmap+0x141/0x210 [qla2xxx]
Remove DMA mapping from the driver altogether, as it is already done by FC
layer. This prevents the warning. |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Fix null pointer dereference in bnxt_bs_trace_check_wrap()
With older FW, we may get the ASYNC_EVENT_CMPL_EVENT_ID_DBG_BUF_PRODUCER
for FW trace data type that has not been initialized. This will result
in a crash in bnxt_bs_trace_type_wrap(). Add a guard to check for a
valid magic_byte pointer before proceeding. |
| In the Linux kernel, the following vulnerability has been resolved:
xen: speed up grant-table reclaim
When a grant entry is still in use by the remote domain, Linux must put
it on a deferred list. Normally, this list is very short, because
the PV network and block protocols expect the backend to unmap the grant
first. However, Qubes OS's GUI protocol is subject to the constraints
of the X Window System, and as such winds up with the frontend unmapping
the window first. As a result, the list can grow very large, resulting
in a massive memory leak and eventual VM freeze.
To partially solve this problem, make the number of entries that the VM
will attempt to free at each iteration tunable. The default is still
10, but it can be overridden via a module parameter.
This is Cc: stable because (when combined with appropriate userspace
changes) it fixes a severe performance and stability problem for Qubes
OS users. |
| In the Linux kernel, the following vulnerability has been resolved:
can: isotp: check CAN address family in isotp_bind()
Add missing check to block non-AF_CAN binds.
Syzbot created some code which matched the right sockaddr struct size
but used AF_XDP (0x2C) instead of AF_CAN (0x1D) in the address family
field:
bind$xdp(r2, &(0x7f0000000540)={0x2c, 0x0, r4, 0x0, r2}, 0x10)
^^^^
This has no funtional impact but the userspace should be notified about
the wrong address family field content. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: lpfc: Prevent lpfc_debugfs_lockstat_write() buffer overflow
A static code analysis tool flagged the possibility of buffer overflow when
using copy_from_user() for a debugfs entry.
Currently, it is possible that copy_from_user() copies more bytes than what
would fit in the mybuf char array. Add a min() restriction check between
sizeof(mybuf) - 1 and nbytes passed from the userspace buffer to protect
against buffer overflow. |
| In the Linux kernel, the following vulnerability has been resolved:
fs: Protect reconfiguration of sb read-write from racing writes
The reconfigure / remount code takes a lot of effort to protect
filesystem's reconfiguration code from racing writes on remounting
read-only. However during remounting read-only filesystem to read-write
mode userspace writes can start immediately once we clear SB_RDONLY
flag. This is inconvenient for example for ext4 because we need to do
some writes to the filesystem (such as preparation of quota files)
before we can take userspace writes so we are clearing SB_RDONLY flag
before we are fully ready to accept userpace writes and syzbot has found
a way to exploit this [1]. Also as far as I'm reading the code
the filesystem remount code was protected from racing writes in the
legacy mount path by the mount's MNT_READONLY flag so this is relatively
new problem. It is actually fairly easy to protect remount read-write
from racing writes using sb->s_readonly_remount flag so let's just do
that instead of having to workaround these races in the filesystem code.
[1] https://lore.kernel.org/all/00000000000006a0df05f6667499@google.com/T/ |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath9k: Fix use-after-free in ath9k_hif_usb_disconnect()
This patch fixes a use-after-free in ath9k that occurs in
ath9k_hif_usb_disconnect() when ath9k_destroy_wmi() is trying to access
'drv_priv' that has already been freed by ieee80211_free_hw(), called by
ath9k_htc_hw_deinit(). The patch moves ath9k_destroy_wmi() before
ieee80211_free_hw(). Note that urbs from the driver should be killed
before freeing 'wmi' with ath9k_destroy_wmi() as their callbacks will
access 'wmi'.
Found by a modified version of syzkaller.
==================================================================
BUG: KASAN: use-after-free in ath9k_destroy_wmi+0x38/0x40
Read of size 8 at addr ffff8881069132a0 by task kworker/0:1/7
CPU: 0 PID: 7 Comm: kworker/0:1 Tainted: G O 5.14.0+ #131
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Workqueue: usb_hub_wq hub_event
Call Trace:
dump_stack_lvl+0x8e/0xd1
print_address_description.constprop.0.cold+0x93/0x334
? ath9k_destroy_wmi+0x38/0x40
? ath9k_destroy_wmi+0x38/0x40
kasan_report.cold+0x83/0xdf
? ath9k_destroy_wmi+0x38/0x40
ath9k_destroy_wmi+0x38/0x40
ath9k_hif_usb_disconnect+0x329/0x3f0
? ath9k_hif_usb_suspend+0x120/0x120
? usb_disable_interface+0xfc/0x180
usb_unbind_interface+0x19b/0x7e0
? usb_autoresume_device+0x50/0x50
device_release_driver_internal+0x44d/0x520
bus_remove_device+0x2e5/0x5a0
device_del+0x5b2/0xe30
? __device_link_del+0x370/0x370
? usb_remove_ep_devs+0x43/0x80
? remove_intf_ep_devs+0x112/0x1a0
usb_disable_device+0x1e3/0x5a0
usb_disconnect+0x267/0x870
hub_event+0x168d/0x3950
? rcu_read_lock_sched_held+0xa1/0xd0
? hub_port_debounce+0x2e0/0x2e0
? check_irq_usage+0x860/0xf20
? drain_workqueue+0x281/0x360
? lock_release+0x640/0x640
? rcu_read_lock_sched_held+0xa1/0xd0
? rcu_read_lock_bh_held+0xb0/0xb0
? lockdep_hardirqs_on_prepare+0x273/0x3e0
process_one_work+0x92b/0x1460
? pwq_dec_nr_in_flight+0x330/0x330
? rwlock_bug.part.0+0x90/0x90
worker_thread+0x95/0xe00
? __kthread_parkme+0x115/0x1e0
? process_one_work+0x1460/0x1460
kthread+0x3a1/0x480
? set_kthread_struct+0x120/0x120
ret_from_fork+0x1f/0x30
The buggy address belongs to the page:
page:ffffea00041a44c0 refcount:0 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x106913
flags: 0x200000000000000(node=0|zone=2)
raw: 0200000000000000 0000000000000000 dead000000000122 0000000000000000
raw: 0000000000000000 0000000000000000 00000000ffffffff 0000000000000000
page dumped because: kasan: bad access detected
page_owner tracks the page as freed
page last allocated via order 3, migratetype Unmovable, gfp_mask 0x40dc0(GFP_KERNEL|__GFP_COMP|__GFP_ZERO), pid 7, ts 38347963444, free_ts 41399957635
prep_new_page+0x1aa/0x240
get_page_from_freelist+0x159a/0x27c0
__alloc_pages+0x2da/0x6a0
alloc_pages+0xec/0x1e0
kmalloc_order+0x39/0xf0
kmalloc_order_trace+0x19/0x120
__kmalloc+0x308/0x390
wiphy_new_nm+0x6f5/0x1dd0
ieee80211_alloc_hw_nm+0x36d/0x2230
ath9k_htc_probe_device+0x9d/0x1e10
ath9k_htc_hw_init+0x34/0x50
ath9k_hif_usb_firmware_cb+0x25f/0x4e0
request_firmware_work_func+0x131/0x240
process_one_work+0x92b/0x1460
worker_thread+0x95/0xe00
kthread+0x3a1/0x480
page last free stack trace:
free_pcp_prepare+0x3d3/0x7f0
free_unref_page+0x1e/0x3d0
device_release+0xa4/0x240
kobject_put+0x186/0x4c0
put_device+0x20/0x30
ath9k_htc_disconnect_device+0x1cf/0x2c0
ath9k_htc_hw_deinit+0x26/0x30
ath9k_hif_usb_disconnect+0x2d9/0x3f0
usb_unbind_interface+0x19b/0x7e0
device_release_driver_internal+0x44d/0x520
bus_remove_device+0x2e5/0x5a0
device_del+0x5b2/0xe30
usb_disable_device+0x1e3/0x5a0
usb_disconnect+0x267/0x870
hub_event+0x168d/0x3950
process_one_work+0x92b/0x1460
Memory state around the buggy address:
ffff888106913180: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
ffff888106913200: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>ffff888
---truncated--- |
