| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
xfs: fix a UAF problem in xattr repair
The xchk_setup_xattr_buf function can allocate a new value buffer, which
means that any reference to ab->value before the call could become a
dangling pointer. Fix this by moving an assignment to after the buffer
setup. |
| In the Linux kernel, the following vulnerability has been resolved:
net: dsa: microchip: Don't free uninitialized ksz_irq
If something goes wrong at setup, ksz_irq_free() can be called on
uninitialized ksz_irq (for example when ksz_ptp_irq_setup() fails). It
leads to freeing uninitialized IRQ numbers and/or domains.
Use dsa_switch_for_each_user_port_continue_reverse() in the error path
to iterate only over the fully initialized ports. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: hda: cs35l41: Fix NULL pointer dereference in cs35l41_hda_read_acpi()
The acpi_get_first_physical_node() function can return NULL, in which
case the get_device() function also returns NULL, but this value is
then dereferenced without checking,so add a check to prevent a crash.
Found by Linux Verification Center (linuxtesting.org) with SVACE. |
| In the Linux kernel, the following vulnerability has been resolved:
media: af9005: Fix null-ptr-deref in af9005_i2c_xfer
In af9005_i2c_xfer, msg is controlled by user. When msg[i].buf
is null and msg[i].len is zero, former checks on msg[i].buf would be
passed. Malicious data finally reach af9005_i2c_xfer. If accessing
msg[i].buf[0] without sanity check, null ptr deref would happen.
We add check on msg[i].len to prevent crash.
Similar commit:
commit 0ed554fd769a
("media: dvb-usb: az6027: fix null-ptr-deref in az6027_i2c_xfer()") |
| In the Linux kernel, the following vulnerability has been resolved:
fs/notify: call exportfs_encode_fid with s_umount
Calling intotify_show_fdinfo() on fd watching an overlayfs inode, while
the overlayfs is being unmounted, can lead to dereferencing NULL ptr.
This issue was found by syzkaller.
Race Condition Diagram:
Thread 1 Thread 2
-------- --------
generic_shutdown_super()
shrink_dcache_for_umount
sb->s_root = NULL
|
| vfs_read()
| inotify_fdinfo()
| * inode get from mark *
| show_mark_fhandle(m, inode)
| exportfs_encode_fid(inode, ..)
| ovl_encode_fh(inode, ..)
| ovl_check_encode_origin(inode)
| * deref i_sb->s_root *
|
|
v
fsnotify_sb_delete(sb)
Which then leads to:
[ 32.133461] Oops: general protection fault, probably for non-canonical address 0xdffffc0000000006: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN NOPTI
[ 32.134438] KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037]
[ 32.135032] CPU: 1 UID: 0 PID: 4468 Comm: systemd-coredum Not tainted 6.17.0-rc6 #22 PREEMPT(none)
<snip registers, unreliable trace>
[ 32.143353] Call Trace:
[ 32.143732] ovl_encode_fh+0xd5/0x170
[ 32.144031] exportfs_encode_inode_fh+0x12f/0x300
[ 32.144425] show_mark_fhandle+0xbe/0x1f0
[ 32.145805] inotify_fdinfo+0x226/0x2d0
[ 32.146442] inotify_show_fdinfo+0x1c5/0x350
[ 32.147168] seq_show+0x530/0x6f0
[ 32.147449] seq_read_iter+0x503/0x12a0
[ 32.148419] seq_read+0x31f/0x410
[ 32.150714] vfs_read+0x1f0/0x9e0
[ 32.152297] ksys_read+0x125/0x240
IOW ovl_check_encode_origin derefs inode->i_sb->s_root, after it was set
to NULL in the unmount path.
Fix it by protecting calling exportfs_encode_fid() from
show_mark_fhandle() with s_umount lock.
This form of fix was suggested by Amir in [1].
[1]: https://lore.kernel.org/all/CAOQ4uxhbDwhb+2Brs1UdkoF0a3NSdBAOQPNfEHjahrgoKJpLEw@mail.gmail.com/ |
| In the Linux kernel, the following vulnerability has been resolved:
vsock: fix lock inversion in vsock_assign_transport()
Syzbot reported a potential lock inversion deadlock between
vsock_register_mutex and sk_lock-AF_VSOCK when vsock_linger() is called.
The issue was introduced by commit 687aa0c5581b ("vsock: Fix
transport_* TOCTOU") which added vsock_register_mutex locking in
vsock_assign_transport() around the transport->release() call, that can
call vsock_linger(). vsock_assign_transport() can be called with sk_lock
held. vsock_linger() calls sk_wait_event() that temporarily releases and
re-acquires sk_lock. During this window, if another thread hold
vsock_register_mutex while trying to acquire sk_lock, a circular
dependency is created.
Fix this by releasing vsock_register_mutex before calling
transport->release() and vsock_deassign_transport(). This is safe
because we don't need to hold vsock_register_mutex while releasing the
old transport, and we ensure the new transport won't disappear by
obtaining a module reference first via try_module_get(). |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon/core: fix potential memory leak by cleaning ops_filter in damon_destroy_scheme
Currently, damon_destroy_scheme() only cleans up the filter list but
leaves ops_filter untouched, which could lead to memory leaks when a
scheme is destroyed.
This patch ensures both filter and ops_filter are properly freed in
damon_destroy_scheme(), preventing potential memory leaks. |
| In the Linux kernel, the following vulnerability has been resolved:
hwmon: (cgbc-hwmon) Add missing NULL check after devm_kzalloc()
The driver allocates memory for sensor data using devm_kzalloc(), but
did not check if the allocation succeeded. In case of memory allocation
failure, dereferencing the NULL pointer would lead to a kernel crash.
Add a NULL pointer check and return -ENOMEM to handle allocation failure
properly. |
| In the Linux kernel, the following vulnerability has been resolved:
most: usb: Fix use-after-free in hdm_disconnect
hdm_disconnect() calls most_deregister_interface(), which eventually
unregisters the MOST interface device with device_unregister(iface->dev).
If that drops the last reference, the device core may call release_mdev()
immediately while hdm_disconnect() is still executing.
The old code also freed several mdev-owned allocations in
hdm_disconnect() and then performed additional put_device() calls.
Depending on refcount order, this could lead to use-after-free or
double-free when release_mdev() ran (or when unregister paths also
performed puts).
Fix by moving the frees of mdev-owned allocations into release_mdev(),
so they happen exactly once when the device is truly released, and by
dropping the extra put_device() calls in hdm_disconnect() that are
redundant after device_unregister() and most_deregister_interface().
This addresses the KASAN slab-use-after-free reported by syzbot in
hdm_disconnect(). See report and stack traces in the bug link below. |
| In the Linux kernel, the following vulnerability has been resolved:
mm/damon/vaddr: do not repeat pte_offset_map_lock() until success
DAMON's virtual address space operation set implementation (vaddr) calls
pte_offset_map_lock() inside the page table walk callback function. This
is for reading and writing page table accessed bits. If
pte_offset_map_lock() fails, it retries by returning the page table walk
callback function with ACTION_AGAIN.
pte_offset_map_lock() can continuously fail if the target is a pmd
migration entry, though. Hence it could cause an infinite page table walk
if the migration cannot be done until the page table walk is finished.
This indeed caused a soft lockup when CPU hotplugging and DAMON were
running in parallel.
Avoid the infinite loop by simply not retrying the page table walk. DAMON
is promising only a best-effort accuracy, so missing access to such pages
is no problem. |
| In the Linux kernel, the following vulnerability has been resolved:
media: v4l2-subdev: Fix alloc failure check in v4l2_subdev_call_state_try()
v4l2_subdev_call_state_try() macro allocates a subdev state with
__v4l2_subdev_state_alloc(), but does not check the returned value. If
__v4l2_subdev_state_alloc fails, it returns an ERR_PTR, and that would
cause v4l2_subdev_call_state_try() to crash.
Add proper error handling to v4l2_subdev_call_state_try(). |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: core: Prevent integer underflow
By using a ratio of delay to poll_enabled_time that is not integer
time_remaining underflows and does not exit the loop as expected.
As delay could be derived from DT and poll_enabled_time is defined
in the driver this can easily happen.
Use a signed iterator to make sure that the loop exits once
the remaining time is negative. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: mpt3sas: Fix crash in transport port remove by using ioc_info()
During mpt3sas_transport_port_remove(), messages were logged with
dev_printk() against &mpt3sas_port->port->dev. At this point the SAS
transport device may already be partially unregistered or freed, leading
to a crash when accessing its struct device.
Using ioc_info(), which logs via the PCI device (ioc->pdev->dev),
guaranteed to remain valid until driver removal.
[83428.295776] Oops: general protection fault, probably for non-canonical address 0x6f702f323a33312d: 0000 [#1] SMP NOPTI
[83428.295785] CPU: 145 UID: 0 PID: 113296 Comm: rmmod Kdump: loaded Tainted: G OE 6.16.0-rc1+ #1 PREEMPT(voluntary)
[83428.295792] Tainted: [O]=OOT_MODULE, [E]=UNSIGNED_MODULE
[83428.295795] Hardware name: Dell Inc. Precision 7875 Tower/, BIOS 89.1.67 02/23/2024
[83428.295799] RIP: 0010:__dev_printk+0x1f/0x70
[83428.295805] Code: 90 90 90 90 90 90 90 90 90 90 90 0f 1f 44 00 00 49 89 d1 48 85 f6 74 52 4c 8b 46 50 4d 85 c0 74 1f 48 8b 46 68 48 85 c0 74 22 <48> 8b 08 0f b6 7f 01 48 c7 c2 db e8 42 ad 83 ef 30 e9 7b f8 ff ff
[83428.295813] RSP: 0018:ff85aeafc3137bb0 EFLAGS: 00010206
[83428.295817] RAX: 6f702f323a33312d RBX: ff4290ee81292860 RCX: 5000cca25103be32
[83428.295820] RDX: ff85aeafc3137bb8 RSI: ff4290eeb1966c00 RDI: ffffffffc1560845
[83428.295823] RBP: ff85aeafc3137c18 R08: 74726f702f303a33 R09: ff85aeafc3137bb8
[83428.295826] R10: ff85aeafc3137b18 R11: ff4290f5bd60fe68 R12: ff4290ee81290000
[83428.295830] R13: ff4290ee6e345de0 R14: ff4290ee81290000 R15: ff4290ee6e345e30
[83428.295833] FS: 00007fd9472a6740(0000) GS:ff4290f5ce96b000(0000) knlGS:0000000000000000
[83428.295837] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[83428.295840] CR2: 00007f242b4db238 CR3: 00000002372b8006 CR4: 0000000000771ef0
[83428.295844] PKRU: 55555554
[83428.295846] Call Trace:
[83428.295848] <TASK>
[83428.295850] _dev_printk+0x5c/0x80
[83428.295857] ? srso_alias_return_thunk+0x5/0xfbef5
[83428.295863] mpt3sas_transport_port_remove+0x1c7/0x420 [mpt3sas]
[83428.295882] _scsih_remove_device+0x21b/0x280 [mpt3sas]
[83428.295894] ? _scsih_expander_node_remove+0x108/0x140 [mpt3sas]
[83428.295906] ? srso_alias_return_thunk+0x5/0xfbef5
[83428.295910] mpt3sas_device_remove_by_sas_address.part.0+0x8f/0x110 [mpt3sas]
[83428.295921] _scsih_expander_node_remove+0x129/0x140 [mpt3sas]
[83428.295933] _scsih_expander_node_remove+0x6a/0x140 [mpt3sas]
[83428.295944] scsih_remove+0x3f0/0x4a0 [mpt3sas]
[83428.295957] pci_device_remove+0x3b/0xb0
[83428.295962] device_release_driver_internal+0x193/0x200
[83428.295968] driver_detach+0x44/0x90
[83428.295971] bus_remove_driver+0x69/0xf0
[83428.295975] pci_unregister_driver+0x2a/0xb0
[83428.295979] _mpt3sas_exit+0x1f/0x300 [mpt3sas]
[83428.295991] __do_sys_delete_module.constprop.0+0x174/0x310
[83428.295997] ? srso_alias_return_thunk+0x5/0xfbef5
[83428.296000] ? __x64_sys_getdents64+0x9a/0x110
[83428.296005] ? srso_alias_return_thunk+0x5/0xfbef5
[83428.296009] ? syscall_trace_enter+0xf6/0x1b0
[83428.296014] do_syscall_64+0x7b/0x2c0
[83428.296019] ? srso_alias_return_thunk+0x5/0xfbef5
[83428.296023] entry_SYSCALL_64_after_hwframe+0x76/0x7e |
| In the Linux kernel, the following vulnerability has been resolved:
can: hi311x: fix null pointer dereference when resuming from sleep before interface was enabled
This issue is similar to the vulnerability in the `mcp251x` driver,
which was fixed in commit 03c427147b2d ("can: mcp251x: fix resume from
sleep before interface was brought up").
In the `hi311x` driver, when the device resumes from sleep, the driver
schedules `priv->restart_work`. However, if the network interface was
not previously enabled, the `priv->wq` (workqueue) is not allocated and
initialized, leading to a null pointer dereference.
To fix this, we move the allocation and initialization of the workqueue
from the `hi3110_open` function to the `hi3110_can_probe` function.
This ensures that the workqueue is properly initialized before it is
used during device resume. And added logic to destroy the workqueue
in the error handling paths of `hi3110_can_probe` and in the
`hi3110_can_remove` function to prevent resource leaks. |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2: fix double free in user_cluster_connect()
user_cluster_disconnect() frees "conn->cc_private" which is "lc" but then
the error handling frees "lc" a second time. Set "lc" to NULL on this
path to avoid a double free. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: don't spin in add_stack_record when gfp flags don't allow
syzbot was able to find the following path:
add_stack_record_to_list mm/page_owner.c:182 [inline]
inc_stack_record_count mm/page_owner.c:214 [inline]
__set_page_owner+0x2c3/0x4a0 mm/page_owner.c:333
set_page_owner include/linux/page_owner.h:32 [inline]
post_alloc_hook+0x240/0x2a0 mm/page_alloc.c:1851
prep_new_page mm/page_alloc.c:1859 [inline]
get_page_from_freelist+0x21e4/0x22c0 mm/page_alloc.c:3858
alloc_pages_nolock_noprof+0x94/0x120 mm/page_alloc.c:7554
Don't spin in add_stack_record_to_list() when it is called
from *_nolock() context. |
| In the Linux kernel, the following vulnerability has been resolved:
dmaengine: apple-admac: Fix 'current_tx' not getting freed
In terminate_all we should queue up all submitted descriptors to be
freed. We do that for the content of the 'issued' and 'submitted' lists,
but the 'current_tx' descriptor falls through the cracks as it's
removed from the 'issued' list once it gets assigned to be the current
descriptor. Explicitly queue up freeing of the 'current_tx' descriptor
to address a memory leak that is otherwise present. |
| In the Linux kernel, the following vulnerability has been resolved:
NFS: Check the TLS certificate fields in nfs_match_client()
If the TLS security policy is of type RPC_XPRTSEC_TLS_X509, then the
cert_serial and privkey_serial fields need to match as well since they
define the client's identity, as presented to the server. |
| In the Linux kernel, the following vulnerability has been resolved:
usb: musb: Fix musb_gadget.c rxstate overflow bug
The usb function device call musb_gadget_queue() adds the passed
request to musb_ep::req_list,If the (request->length > musb_ep->packet_sz)
and (is_buffer_mapped(req) return false),the rxstate() will copy all data
in fifo to request->buf which may cause request->buf out of bounds.
Fix it by add the length check :
fifocnt = min_t(unsigned, request->length - request->actual, fifocnt); |
| In the Linux kernel, the following vulnerability has been resolved:
jbd2: fix potential buffer head reference count leak
As in 'jbd2_fc_wait_bufs' if buffer isn't uptodate, will return -EIO without
update 'journal->j_fc_off'. But 'jbd2_fc_release_bufs' will release buffer head
from ‘j_fc_off - 1’ if 'bh' is NULL will terminal release which will lead to
buffer head buffer head reference count leak.
To solve above issue, update 'journal->j_fc_off' before return -EIO. |
