| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-multipath: fix underflow in ANA log bounds checks
The number of ANA groups advertised through Identify Controller sizes the
ANA log buffer. The ANA log header and group descriptors independently
supply the number of groups and namespace IDs to parse.
Both bounds checks subtract an untrusted object size from ana_log_size
before comparing the current offset. If the object is larger than the
buffer, the size_t subtraction underflows and lets the parser read beyond
ana_log_buf.
Check the current offset before the first subtraction and compare each
object size with the remaining buffer instead. This rejects inconsistent
ANA data before dereferencing a truncated group descriptor or walking an
oversized namespace ID array. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cw1200: fix TX padding OOB read leaking heap data to device
The TX path rounds the transfer size up to the bus alignment
(align_size(), up to 511 bytes for SDIO, 1 byte for SPI) but sends
the padded length straight from the frame buffer, which has no room
reserved for the padding. cw1200_data_write() therefore reads past
the end of the frame and the bus transfer carries those bytes to the
device. A bogus device can collect up to 511 bytes of kernel heap
data per TX frame.
The RX path does not have this problem: it allocates the skb with
the aligned length (alloc_len) before reading.
Compute the exact padding with the bus align_size() callback, make
sure queued TX frames have tailroom for it, and zero the padding
bytes before the transfer so nothing past the frame is exposed.
This is not expected to change driver behavior on most cases: frame
contents and transfer sizes are unchanged, only the content of the
padding bytes (previously undefined stale memory, now zero), which
the device never reads since the WSM header carries the real frame
length. The skb expansion can only fail under memory exhaustion,
in which case the frame is dropped like on the existing error paths
of cw1200_tx().
Discovered by Atuin - Automated Vulnerability Discovery Engine. |
| In the Linux kernel, the following vulnerability has been resolved:
perf: Require kernel access for text poke events
Perf events with exclude_kernel=1 can be opened without kernel perf
access. However, exclude_kernel does not suppress text-poke sideband
records. Every PERF_RECORD_TEXT_POKE is marked PERF_RECORD_MISC_KERNEL
and contains a raw kernel instruction address.
An unprivileged task can therefore open and mmap a task-local software
event with text_poke=1. Both opening a count-only tracepoint event and
configuring UDP GRO for ESP-in-UDP cause updates to inline static calls;
the observer receives the relocated addresses of the modified instructions.
For a known kernel image, any such address reveals the runtime kernel
text base despite KASLR.
Call perf_allow_kernel() whenever attr.text_poke is set, regardless of
exclude_kernel. Events that neither monitor kernel execution nor request
text-poke records retain their existing permissions. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdkfd: fix SMI event cross-process information leak
kfd_smi_ev_enabled() skips the suser privilege check when pid=0.
PROCESS_START, PROCESS_END, and VMFAULT events are emitted with
pid=0 while carrying another process's PID and command name, so any
/dev/kfd user in the render group can monitor all GPU workloads.
Pass the target process PID into kfd_smi_event_add() for these events
so the existing per-client filter restricts delivery to the owning
process or CAP_SYS_ADMIN subscribers. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: iwlwifi: mvm: validate TX_CMD response layout
TX_CMD parsing uses frame_count to walk status entries and then
read the trailing SCD SSN. Make the minimum-length check follow
that exact runtime layout calculation before parsing the payload.
For new TX API, reject TX_CMD responses with frame_count != 1 and
warn/return in the aggregation handler to document that aggregated
accounting is expected via BA notifications. |
| In the Linux kernel, the following vulnerability has been resolved:
i3c: master: Do not treat master device as a duplicate target
i3c_master_search_i3c_dev_duplicate() searches the bus for another I3C
device with the same PID as the reference device. The search can match
master->this, causing the controller itself to be returned as a
duplicate.
Since the controller is not a target device, it cannot be a duplicate of
one. Exclude master->this from matching so that the function only
returns real duplicate target devices. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Copy per-CPU map value padding in copy_map_value_long()
In kernel, per-CPU map elements are stored with
round_up(map->value_size, 8) bytes. On UAPI lookup paths, it copies the
rounded size for each CPU into a temporary buffer.
However, copy_map_value_long() passes 'map->value_size' to
bpf_obj_memcpy(). When the map has special fields, bpf_obj_memcpy() copies
around those fields with memcpy(), and does not copy the tail padding
between 'map->value_size' and round_up(map->value_size, 8).
The temporary UAPI lookup buffers are allocated without __GFP_ZERO. As a
result, when the per-CPU map's value size is not equal to
round_up(map->value_size, 8), UAPI LOOKUP_ELEM and its variants can return
stale heap contents from that padding to user space. The same issue
applies to bpf_iter for per-CPU maps.
Pass round_up(map->value_size, 8) to bpf_obj_memcpy() from
copy_map_value_long(), so per-CPU maps both with and without special
fields copy the entire per-CPU slot. Remove the now redundant round_up()
from bpf_obj_memcpy()'s long_memcpy path. |
| In the Linux kernel, the following vulnerability has been resolved:
time/namespace: Validate nanosecond field in proc_timens_set_offset()
The function validates tv_sec to be within [-KTIME_SEC_MAX, KTIME_SEC_MAX]
but never validates that tv_nsec is within the valid range of
[0, NSEC_PER_SEC-1] before using it in timespec64_add().
timespec64_add() expects both timespec64 structures to have normalized
values with tv_nsec in the range [0, 999999999]. If off->val.tv_nsec
contains invalid values (negative or >= NSEC_PER_SEC), it could lead to
incorrect calculations or unexpected behavior.
Add validation to ensure tv_nsec is within the valid range before
performing the addition. |
| In the Linux kernel, the following vulnerability has been resolved:
firmware: arm_scmi: Reject out of range DT protocol IDs
SCMI protocol IDs carried in message headers are limited by
MSG_PROTOCOL_ID_MASK. The DT parsing paths noticed protocol IDs
outside that range, but only logged an error and then kept processing
the invalid value.
That lets a malformed 32-bit DT reg value reach helpers which take a u8
protocol ID, where it can be truncated and/or treated as a different
protocol.
For channel setup, two different out-of-range values can also be used as
distinct IDR keys while aliasing the generated SCMI protocol identity.
Skip DT protocol nodes whose reg value does not fit the SCMI protocol ID
field before setting up channels or creating protocol devices. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Zero queue and stack outputs on lock failure
Queue and stack pop/peek helpers accept an uninitialized output buffer
because the verifier expects the helper to initialize it. The empty-map
error path clears the buffer, but a failed lock acquisition returns
-EBUSY without writing it.
Clear the output before returning -EBUSY so BPF programs cannot observe
uninitialized stack contents after a failed helper call. |
| In the Linux kernel, the following vulnerability has been resolved:
arm64: ptrace: Keep 'orig_x0' in-sync with x0 on syscall entry
Commit e057b9477232 ("arm64: syscall: Ensure saved x0 is kept in-sync
with tracer updates") attempted to resolve a long-standing issue with
syscall entry tracing, where a tracer is able to manipulate the first
syscall argument without being subjected to seccomp or audit checking.
Unfortunately, that fix was incomplete [1], as it failed to update
'orig_x0' between a tracer updating x0 during a seccomp ptrace exit
(SECCOMP_RET_TRACE) and the seccomp filter being re-evaluated.
Rather than add hooks to the core seccomp code, instead move the
synchronisation code into the ptrace GPR and syscall setting code so
that 'orig_x0' is kept up to date with x0 whenever we're stopped on the
syscall entry path. |
| In the Linux kernel, the following vulnerability has been resolved:
HID: steam: Reject short reads
Steam Controller FEATURE reports encode the size of the message in the
message itself. Previously we were trusting that the size reported matched
the size we actually read, leading to a potential issue with short reads.
Instead, we should actually verify the length of the read. |
| In the Linux kernel, the following vulnerability has been resolved:
coresight: etm4x: missing cscfg_csdev_disable_active_config() in perf enable
In the perf enable path, there are missing cases where
cscfg_csdev_disable_active_config() is not called:
- Branch broadcast is selected but not supported by the hardware
- etm4_enable_hw() fails
This can lead to a leak of config_desc->active_cnt.
Fix this by properly calling cscfg_csdev_disable_active_config()
in these error paths. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: seq: Don't leak the extension cell pointer in the bounce payload
The bounce_error_event() embeds the failed event in the bounce payload
by pointing data.ext.ptr at it. When that event is a queued
variable-length event, its own data.ext.ptr holds the address of its
first extension cell, put there by snd_seq_event_dup(). The payload
goes out verbatim through snd_seq_expand_var_event(), so the address
reaches userspace.
That is the same address commit 705dd6dcbc0e ("ALSA: seq: Clear
variable event pointer on read") removed from the event header. The
read path still clears it there, just above the call that expands the
payload.
Embed a sanitised copy instead, treated exactly as snd_seq_read()
treats the header. A stack copy is enough because delivery is
synchronous and snd_seq_event_dup() copies before returning.
An unprivileged client reaches this by setting SNDRV_SEQ_FILTER_BOUNCE,
queueing a variable-length event to a port that does not exist and
reading the bounce back. Eight bytes on 64-bit, from its own pool. |
| In the Linux kernel, the following vulnerability has been resolved:
ocfs2: validate orphan slot during inode read
Patch series "ocfs2: validate active orphan slots during inode read".
OCFS2 trusts active ordinary and append-DIO orphan slots read from dinodes.
A corrupted slot can therefore index osb_orphan_wipes or the slot-local
system-inode cache outside their allocations before the corruption is
reported.
Patch 1 validates the ordinary orphan slot used by inode wipe processing.
Patch 2 validates the append-DIO orphan slot used by DIO completion and
orphan recovery. Both checks reject corrupt metadata at the existing inode
validation boundary.
This patch (of 2):
[BUG]
A corrupted dinode with OCFS2_ORPHANED_FL can carry an
i_orphaned_slot outside the mounted filesystem slot range.
ocfs2_wipe_inode() uses it to index osb_orphan_wipes before looking
up the orphan directory, causing an out-of-bounds memory access.
BUG: KASAN: slab-use-after-free in ocfs2_get_system_file_inode+0x780/0x820 fs/ocfs2/sysfile.c:102
Read of size 8 at addr ffff88800b767c00 by task kworker/u8:3/85
Call Trace:
...
ocfs2_get_system_file_inode+0x780/0x820 fs/ocfs2/sysfile.c:102
ocfs2_wipe_inode+0x292/0xf70 fs/ocfs2/inode.c:840
ocfs2_delete_inode fs/ocfs2/inode.c:1155 [inline]
ocfs2_evict_inode+0x6c9/0x1170 fs/ocfs2/inode.c:1295
evict+0x38e/0x8f0 fs/inode.c:810
iput_final fs/inode.c:1914 [inline]
iput fs/inode.c:1966 [inline]
iput+0x55b/0x8b0 fs/inode.c:1926
ocfs2_recover_orphans+0x610/0xe40 fs/ocfs2/journal.c:2374
ocfs2_complete_recovery+0x5af/0xd00 fs/ocfs2/journal.c:1373
...
[CAUSE]
ocfs2_validate_inode_block() validates i_suballoc_slot but leaves
the active ordinary orphan slot unchecked. Downstream consumers
assume that the value is smaller than osb->max_slots.
[FIX]
Reject an active i_orphaned_slot outside the slot range during
dinode validation, before the inode reaches orphan wipe processing. |
| In the Linux kernel, the following vulnerability has been resolved:
erofs: fix interlaced ztailpacking pclusters
On-disk sizes of interlaced pclusters should be block-aligned, and
ztailpacking interlaced pclusters should be invalid at all.
Currently, mkfs.erofs won't generate any interlaced pcluster with
ztailpacking enabled, so this doesn't affect any existing valid
filesystems.
However, crafted images can contain invalid interlaced ztailpacking
pclusters, resulting in an out-of-bounds read from a kmap'd page and
copying irrelevant kernel memory into userspace-visible page cache. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, xdp: move offload check into dev_xdp_install()
bpf_xdp_link_update() calls dev_xdp_install() directly and skips
dev_xdp_attach(), so the checks in dev_xdp_attach() do not run. A user can
make an XDP link with a normal program and then swap in an offloaded or
device-bound program with BPF_LINK_UPDATE, which puts it on the software
path.
dev_xdp_install() is the one place all three paths go through:
"ip link set xdp" and BPF_LINK_CREATE reach it via dev_xdp_attach(), and
BPF_LINK_UPDATE calls it directly. So move the program checks (offloaded,
bound to another device, device-bound in generic mode, native vs generic,
DEVMAP and CPUMAP) there, and keep only the netlink-flag check
(XDP_FLAGS_UPDATE_IF_NOEXIST) in dev_xdp_attach(). |
| In the Linux kernel, the following vulnerability has been resolved:
net: qlcnic: validate unified ROM sections before loading
The unified ROM parser reads directory, product, and data-descriptor fields
from the firmware file. Existing validation forms table and data ends with
unchecked additions and multiplications. Malformed values can wrap before
they are compared with the firmware size. The parser also dereferences
typed pointers at firmware-controlled offsets.
Valid descriptor extents alone are insufficient for the consumers. The
loader reads a fixed-size bootloader regardless of its declared size, the
version parser assumes a 17-byte tail, and a partial final firmware word is
read as a full u64. A truncated image can therefore make the driver read
beyond the firmware allocation during validation or loading.
Replace the pointer-returning parser with bounded range helpers. Validate
table entry sizes, descriptor indices, section ranges, the fixed
bootloader load length, and the version tail before exposing any section.
Read all file fields with unaligned little-endian accessors and assemble a
partial final word from only the bytes that remain. Apply the same range
checks to the legacy image before reading its fixed fields. |
| In the Linux kernel, the following vulnerability has been resolved:
nvme-fabrics: fix DHCHAP secret leak on parse failure
nvmf_parse_options() duplicates dhchap_secret and dhchap_ctrl_secret
with match_strdup() before validating the DHHC-1: representation.
If validation fails, the parser returns -EINVAL before the temporary
string in p is assigned to opts->dhchap_secret or
opts->dhchap_ctrl_secret. nvmf_create_ctrl() subsequently frees opts,
but nvmf_free_options() cannot release the unassigned temporary string.
Each rejected option therefore leaks one allocation.
This is easy to miss because valid secrets transfer ownership to opts
and are freed normally, while the malformed-secret path still returns
the expected -EINVAL to userspace.
With CONFIG_NVME_HOST_AUTH enabled, the leak is reachable before the
required-option checks and transport lookup. No NVMe-oF target or
working transport connection is required; for example, repeatedly
writing
dhchap_secret=BAD
or
dhchap_ctrl_secret=BAD
to /dev/nvme-fabrics deterministically takes the leaking parse path.
Free the temporary string before leaving both validation error paths.
Use kfree_sensitive() because the copied option may contain secret
material even when its representation is rejected, matching the
sensitive cleanup used for stored DHCHAP secrets. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: qla2xxx: Zero dport diagnostics buffer to avoid info leak
qla2x00_do_dport_diagnostics() allocates the qla_dport_diag response
buffer with kmalloc_obj() (non-zeroing) and, on success, copies the full
sizeof(*dd) back to user space via sg_copy_from_buffer(). The inbound
sg_copy_to_buffer() only fills as many bytes as the user request payload
provides, and qla26xx_dport_diagnostics() zeroes only dd->buf. The
options and unused[] fields are therefore copied out uninitialized,
leaking kernel heap contents to user space.
Allocate with kzalloc_obj(), matching qla2x00_do_dport_diagnostics_v2(). |
